Storm | 4K - Fast - I may be stirring the pot on this one

Posted Apr 30, 2022, 5:29 PM UTC

013
donky23•

Factory polish has almost always been for shelf appeal anyway.

3
jaypeesmithOP•

So, this video shows Storm getting away from 1500-polished to a 4000-sanded finish on their balls, even for long-existing lines.

This is where I stir the pot.

Is this a response to the hardness testing that resulted in the ball bans or is this just coincidental timing?

1
Eddie_PBeer Frame is the Best Frame•

On the surface it looks like a response to the ball bans. Going to a sanded finish allows them to keep the same covers, without the hassle of the polish affecting the outcome of random spot checks. That said, it takes time to replace equipment in a manufacturing plant. They can't just go buy industrial grade equipment off the shelf (I assume). Could go either way... but the perception is all the matters, and the perception is this is a simple way to get their balls into compliance.

1
LolFuPoosyModz2-Hander // 212 PB // 610 HS•

Most likely a bit of both. I’m sure they weren’t at a stand still with research & development on new things to try. But at the same time, with all the news & controversy surrounding their brand, they had to push out their new technology. Probably saves balls from getting back ordered because (i believe?) it eliminates the polishing/compound step of the ball-making process

1
ILikeOatmealMore•

Is this a response to the hardness testing

If you watch the Storm video put out literally the day before this one, https://www.youtube.com/watch?v=sKCtQ63FRQo , they show how the polish on the durometer needle can change the reading of the durometer by a point or two. Considering that per the data released by USBC that many of the balls on the naughty list today are too soft by only a point or two, I think that the connection is obvious. They don't have to worry about USBC taking new out-of-the-box balls (with polish, no polish, whatever the OEM chooses to ship them with), testing them, and if all the other randomness that goes into hardness testing bounces against Storm, the polish on the ball being the variable that pushes the readings under 73D and starting this whole rigmarole all over again.

In short, it seems a way to give Storm a little buffer without having to majorly change processes and materials, and considering how closely they seem to be manufacturing to the limit, right now they need a little buffer.

1
Bowler_300the answer is always hyroad•

It gets worse. They did a barrage of IG story posts this week. Every single ball they tested from all the returns pass at 73/74. And then destroyed them.

1
jaypeesmithOP•

I saw that. The part that has me laughing in all this is that they've also put out videos basically saying that testing with a durometer can produce varied results, implying that such testing is not trustworthy. So, how can you, on one hand, say that something is not trustworthy but then say we should trust that the results that you're showing are accurate?

3
ILikeOatmealMore•

such testing is not trustworthy

it is a small quibble, but I would not imply that said testing is 'not trustworthy', but that hardness testing has a degree of randomness or variance that is known (again see their own video). This is a function of the difficulty of measuring hardness; it is not the same as measuring a length or a temperature.

A test can be trustworthy, even if it has high variance on any individual measurement, especially if that variance is understood and the final aggregate results handle that variance statistically correctly. And that variance is one of the reasons the USBC Process requires at least 10 different tests all around the surface of the ball.

1
ILikeOatmealMore•

they == Storm? or they == USBC? I don't have IG so I can't look myself...

1
jaypeesmithOP•

Storm

2
DemoflowerLad193/300/689 - USBC Youth, Tweener•

Will Storm leave up their instructions on how to get 1500 grit polish(5k+polish) or am I gonna have to specify that to my pso when I resurface my ball?

1