r/1911•
EagleCatchingFish

1911s that reliably feed flat nosed and hollowpoints?

I've got an R1 that works really well, but doesn't feed hollowpoints. My dad is looking to get a 1911, but a lot of his reloads are and will be hollowpoints. Is there a particular, reasonably priced make that tends to do well with hollowpoints? He's partial to Ruger, and would probably just buy that if it works well with a variety of ammo.

Posted Jul 14, 2022, 9:07 AM UTC

722
unusualj107•

Just a heads up. Firing reloads out of any gun will usually void the warranty should anything go wrong. Never tell your manufacturer that's what happened should anything ever... happen. Second. I have found most 1911s will feed hollowpoints if you polish the barrel feed ramp to a mirror polish.

8
EagleCatchingFishOP•

Thanks for the info. I'll give the polishing a shot. What I now mean to have said is that I would never shoot reloads--only factory ammo 😉.

1
Trident731•

You want a 1911 with a ramped barrel.

7
TheDreadnought75•

I haven’t had any problems with my Colt Combat Elite.

5
NeedSuppresiveFire•

Try Federal Punch (230gr). CBC Gold Hex (185gr) and Fiocchi Black Mamba (185gr)

Those are hollow points and feed very well with ZERO malfunctions in most 1911 ive seen.

Gold Hex or Black Mamba + Wilcon Combat magazine = ZERO malfunctions.

5
pewpewpew2232•

Don’t have any issue with my Springfield or tow RIA.

3
James_Dean95•

Is it an Emissary or Ronin? Those are the two on my wishlist.

1
pewpewpew2232•

Mines a stainless Mil Spec

1
geenstrips•

I have not had that issue with any 1911 I have owned. including Tisas, Kimbers, Sig, Dan Wessons, Les Bear and Wilson.some mag issues yes and one or two that needed new slide stops as they would not lock back after the last round. If you are shooting reloads make sure you try a couple of brands of good factory hollow points. I had a Kahr that hung up with hollow points and it shot Speer gold dots better than most.

3
EagleCatchingFishOP•

Sounds good. I'll take a look at the gold dots. I think the reloads he made were Hornady XTP. I'll have to see what he's loading now.

1
1911mark•

Polish the feed ramp AND get Wilson combat magazines!

3
dr4gon2000•

Any decent 1911 will feed hollow points

3
brous475•

I have an R1 enhanced and it eats everything, but Remington does have QC issues (apparently they are better since they came back from bankruptcy ). I only use Wilson or Ed Brown mags, I would try those first. If there are still problems, then try polishing the feed ramp. As for your Dad: Ruger, Sig, S&W, Springfield and Colt are good mid-tier options

2
EagleCatchingFishOP•

I'll let him know. He saw the Springfield Garrison and liked it. I suspect that's the one he'll go with if he buys one. Thanks for the info.

1
Human_Ad_8442•

All of them

2
DieInADitch•

No issues with Armscor.

2
KillaKerbow•

I had a problem with my ATI feeding hollow points as I was upgrading it. All I had to do was take a Dremel tool to the barrel opening ramp where the bullets first contact. Just lower the angle a bit and polish it up real good and it should even feed empty brass reliably the way I was able to get mine to.

2
EagleCatchingFishOP•

Thanks for the info. I'll take a look at it and polish it up.

1
Full_Otto_Bismarck•

What matters is if the individual gun was built right, particularly the frame ramp being properly cut which is critical and there is no tolerance, its either right on the money or its bad.

I have a stone stock Colt 1911 made before WW2. It will feed empty cases from a GI magazine.

2
Rickf6b•

Bul has run everything I've tried

2
Phobos223•

Never had issue with sig, s&w, brown, wilson or nighthawk

2
[deleted]•

[removed]

1