r/Duramax•
GFuggitt

Does this look like a leak and soot? LBZ lifted and tuned, noticing a lack of power under heavy throttle. Don’t hear anything new and no codes.

Does this look like a leak and soot? LBZ lifted and tuned, noticing a lack of power under heavy throttle. Don’t hear anything new and no codes.

Posted Sep 8, 2022, 5:09 PM UTC

1131
1Sjones3•

I would say you have oil coming through the pcv system, it gathers on that side of the turbo inlet. No oil there to leak on the turbo piping. Give it a wash and see what it looks like after a couple days. The soot would be a lot worse if you had a exhaust leak.

8
The_crook•

I would agree. Looked just like mine till I relocated the PCV.

8
Thatldodonkey•

Looks like you have a loose fitting or a crack in the boot.

4
GFuggittOP•

The boot is pretty cheap on rock auto so I’ll order one but I don’t know that it’s leaking.

2
Thatldodonkey•

Did you test the straps and see if they are loose? Those straps can loosen over time due to vibration. I would check that first.

3
GFuggittOP•

They are tight, but now I am getting P0087, and P003a code. I have a lift pump from Kennedy diesel that I’ve been meaning to install when I have some time. Just like the old saying “if you don’t make time for maintenance the truck will take the time for repairs”. Hopefully the p003a was just a fluke or somehow related.

1
9184600•

Got the same thing on my lbz

4
dingowingodogo•

I have the same spot on my LML. I haven't noticed a reduction in power though. I figured I had just spelled something that had collected dust like oil or brake fluid.

4
CRobinsFly•

That's most likely just some oil residue from the charge pipe which is causing road dust to stick to it. I wouldnt worry about it but you could tighten the clamps a bit more.

3
thermobaric74•

It's a factory design... Feature. If you want you can pull the fender liner out, disconnect the upper and lower boots, then twist and slide the whole thing out the fender well. Use Dawn or whatever to clean the boots. But you must get them absolutely oil-free or they'll blow apart. Easiest just to clean off the outside and tighten the clamps. On my LBZ you have to tighten the piss out of them...

3
GFuggittOP•

Gotcha, I don’t think this is my issue for power loss.

1
thermobaric74•

Definitely not. Have you replaced both the fuel and air filters with OEM? Boost under max load when you lose power, and desired vs actual fuel rail pressure?

1
GFuggittOP•

I don’t have a monitor just a cheap obd2 scanner to pull codes, I may be able to get live boost numbers though. I have a CAT fuel filter with adapter/stock primer head and SnB cold air intake, 4” exhaust from stock down tube, efi tunes by Duramaxtuner. It usually runs great and can spin the 37” tires when I want to, but rarely do I go WOT. Only 135,000 miles and I add oil to the fuel, so hopefully the CP3 just needs a little help. I’ll get the Kennedy pump installed asap, but my wife’s grand Cherokee is in the shop atm.

1
thermobaric74•

That CAT filter, the 1R-750 I assume, doesn't sequester water. Not a good idea. The Donaldson P553203 will, and it'll thread into the same adapter. Others will too.

A lift pump won't cure whatever is causing the problem, but it may correct it for the time. Kennedy is what I would choose if I went that route.

There are some really good ELM327 odbII adapters for about $75. Most of the ones on Amazon are terrible Chinese knockoffs. Check out the Car Scanner Pro app website for info.

Lastly, when did you last clean between the rad and intercooler? Although that's commonly the cause of heating issues, and when the intercooler can't cool the charge of air, it also suffers from power loss. You might want to look at "cleaning the stack" mine had a ton of bees in it from when I drove through a swarm and didn't even know it.

/R

1
stilhere•

I've seen those boots fail. Maybe take it off and inspect.

2
speed-addiction•

While you're there/if possible I'd grab a hot side pipe and replace both coupler

2
GFuggittOP•

Why replace the pipe if it’s just the rubber boot?

2

You can fit a 3inch hot side pipe that has fewer bends Stock is 2.5 inches and has a bad 90 degree elbow at the bottom intercooler. 3 inch flows more air and helps lower EGTs. Turbo flange is 2.5 inches but intercooler flange are 3inch why they chose a 2.5 inch pipe to connect is beyond me.

4
speed-addiction•

Bingo

1
GFuggittOP•

Not sure I’m going that route but where can I get the upsized pipe, and will the same replacement boots fit?

1

Just google dura,as hot side intercooler pipe. Your after intercooler pipe is already 3 inch so really only need the hot side from turbo to intercooler

2
[deleted]•

[deleted]

1
erob83•

When's last time the fuel filter was changed

1
GFuggittOP•

Fairly new filter probably less than 3,000 miles on a CAT filter, but I think this is my power issue. Got the dreaded P0087 and P003A codes after checking the bolts on that boot. I have a Kennedy lift pump that I need to install. Hopefully the P003a was just a fluke.

1

PCV delete?

1
GFuggittOP•

I have not, maybe I need to. I do have the EGR blocked but that’s the other side.

1