AlternateContent

Need some Ethernet run.

Titles says it all.

Has anyone had success doing this? I've run into so many issues due to the processor being a 32 bit and minimal guides out there, anyone able to help?

I have a Pi3 for OctoPi and I am a bit wary if running both.

Edit:

I got the Docker container to work. I followed:

Pre req: I used the Debian Buster image from https://www.armbian.com/tinkerboard/ at the bottom of the page. Fresh install on the Tinkerboard. I also set a static IP and hostname defined on my PFSense.

1. https://blog.alexellis.io/first-impressions-asus-tinkerboard/ for some overview
2. https://docs.docker.com/engine/install/debian/#install-using-the-convenience-script for Docker install
3. https://doc

Has anyone run across this issue?

I am thinking of putting a piece of plywood under to extend it, but worry if it will look funny and want to see if anyone else has done this and made it look nice.

No, I will not just buy a bigger stand.

Hello, I am a newbie. Started with some outdoor plants, but winter is coming around and we migrated to an AeroGarden. As I am a bit of a maker, I want to work on an AeroGarden clone.

I was wondering what LEDs they use to get an idea of what to source? If not, I would like to know what the community may think are comparable LEDs?

As it is, I'm looking at Samsung diodes, but would prefer a prebuilt panel/strips.

I am trying to keep the form factor close to the AeroGarden for my implementation, and please skip the whole "better setups" and the obligatory "try Kratky" recommendations.

I am not trying to make an optimized or high yield solution, but a sub $50 alternative.

Thank you in advan

I have a remote for an adjustable mattress that is no longer functional due to me being overzealous. The remote is expensive ($100+). I attempted to hook up a logic analyzer, with no experience of course, and I damaged the copper runs. So from here, I want to try to go mechanical.

Has anyone seen a project of a few solenoids to push a few buttons?

I found this https://www.reddit.com/r/maker/comments/95wfz2/i_built_a_midi_player_piano_with_solenoids_3d/, but it's a bit to the left of what I'm looking for.

I can't seem to find a go-to for these setting, and I am inquiring if anyone has any luck or a config? I got my nozzle in, but haven't opened it due to the uncertainty of if it will work.

I do have the Micro Swiss All Metal Hotend with Slotted Cooling Block for Wanhao i3 w/.4mm Nozzle installed for potential gains in volumetric flow to accommodate an increase nozzle size, but unsure if it will accommodate a 0.8mm.

Please do not link the webpage that states it, I know what it says, but recently, I have had 3 stores tell me different policies and 2 of them stated they couldn't do it because 1, they offered free assembly at that store, so can't adjust to new price, and the 2nd, the item says 1 hour pickup, and that means they cant adjust the price. Whats the deal?

Hello all,

Back story, bought the drying 2nd hand, appears to be from 2006 from Appliance411 (no idea if the site is accurate):

Brand: Kenmore Type: Dryer Country: USA Model: 11067522600 Serial: MT3205136

After running a load for a little, the dryer stopped and a burning smell was inside the room. I could not determine if it was electrical, but I checked the vent, which seemed pretty clear and lint trap, which was clean (always cleaned before load). I figured eh, ran it and kept my eye on it for about 20 minutes, and realized the knob was not advancing, set it to timed air dry for 10 minutes, stayed in the same spot for 15 minutes. So an additional issue, the dryer still seemed to hea

What scores did those who took his practice tests get prior to passing the CySA+?

For the Sec+ I was scoring around 85-90 consistently amongst the 6 practice tests, and passed pretty nicely, is this similar to the CySA+ tests?

Thank you.

I got the triad and am going to get the CySA+ within the next few weeks. Has anyone been in this position? Specifically, what would be a step you've taken to put the cherry on top of your 1 scoop vanilla sundae of experience?

Thanks folks

It smells like eggs, and I believe it's sewage gases(can't say I've got experience with that smell).

My thoughts are the AAV is bad since there is a P traps dedicated to the dishwasher, but haven't tested it.

Dishwasher is to the left.

Here's the pics:

http://imgur.com/a/UU1tqys

Edit: Smell is most noticeable under sink and seems to emit from there.

Edit for anyone passing by, it was my AAV. Took 5 minutes to screw on since there was already a screw on mount.