Blockhead2322

https://moxfield.com/decks/WNf8_aDbCkqIdMpmCXlQmg

I started with the Host of Mordor precon and replaced quite a few cards to streamline the deck a bit. I ended up adding more red cards and as such my mana distribution needed to be updated. I have tried various sources to get a consensus on my mana distribution between all 3 colors and tapped vs untapped entries, but no two sites give me the same advice.

I have a few mana cards coming in the mail, but wanted to see what the experts on here currently think. Looking for any assistance with mana distribution, what to replace with my new mana cards coming in, and general advice for the deck in general. The deck simply aims to build a big orc a

Hello! I am looking for some guidance for building my first commander deck using Doran. These are the cards I currently have, but I feel like it may be a little creature heavy or undertuned with the creatures themselves. Looking for suggestions for the deck as a whole and if I need to add/remove anything major. All help is greatly appreciated!

Thanks!

Shamanic Revelation Druid Class Nightshade Dryad Harmonize Golgari Signet Sol Ring Command Tower Selesnya Signet Assault Formation Path of Ancestry Fellwar Stone Entish Restoration Nature’s Lore Emerald medallion Commander’s Sphere Elvish Mystic Tree of Redemption Timber Protector Indomitable Ancients Ikra Shidiqi, the Usurper Colfenor,

Hope this was formatted correctly. I am attempting to write a script that installs an Intel UHD driver. The idea behind the script is that it will check if an older version of the driver is already installed, and install the driver if it is not up to date or not installed. It will also check if the current version of the driver is already installed. The code does not throw any errors, but I suspect that it is getting hung up at $driverVersion -ne $expectedVersion if the WMI does not return anything when the driver is not installed. Could someone provide a suggestion for me on how to address this or simplify my script process here?

Thanks!

Write-Host "Getting drivers..."

Try {
	# Defin

I am going to explain everything that has happened just as it happened to help with troubleshooting. I started the day doing some basic PID tuning and bringing up the sliders a notch or two to get maybe +5-7 in P and D to fix a slight oscillation problem I had. I then watched Joshua Bardwell's video "Betaflight 4.2 the first 5 changes you should make" and I changed the frequencies of the dynamic notch filter to what he describes in the video.

I set up to fly at a tennis court to film some buddies and I tested the changed and did a few fast sharp 180 turns for about 30 seconds before I landed because I had worse oscillations than before. It was fine for regular flight, just not as tight a

I am going to explain everything that has happened just as it happened to help with troubleshooting. I started the day doing some basic PID tuning and bringing up the sliders a notch or two to get maybe +5-7 in P and D to fix a slight oscillation problem I had. I then watched Joshua Bardwell's video "Betaflight 4.2 the first 5 changes you should make" and I changed the frequencies of the dynamic notch filter to what he describes in the video.

I set up to fly at a tennis court to film some buddies and I tested the changed and did a few fast sharp 180 turns for about 30 seconds before I landed because I had worse oscillations than before. It was fine for regular flight, just not as tight as I

I recently discovered that my old M9 gimbal was not working and had a drift of 5-50 micro seconds. I ordered a new one thinking that maybe the sensor was going bad, but the new gimbal has the yaw completely unresponsive. Is this something that I maybe have to configure in the radio? I ordered another M9 a year ago and had the exact same problem. Ultimately, I’ve had 3 M9 gimbals all with some kind of yaw issue. Is this common? Thanks.

I am finally getting a GoPro Hero 7, but I am a little confused about ND filters and lens protectors. Are ND filters replacing lens protectors or do lens protectors go overtop the ND filters as well? Is it a one or the other type of thing or are they supposed to be best used in combination with one another. I am looking at these Freewell ND filters (link below), but I am wondering if I would place a lens protector overtop them. I am also looking at both the Camera Butter and Ethix ND filters. Can someone help me by clarifying an answer to my question or recommend a good set of affordable ND filters/screen protectors? Thanks!

Freewell ND filters -

[https://www.amazon.com/dp/B01N66IDPN/ref=c

EDIT: SOLVED

Yesterday I flew two packs on my maiden flight with a new build. Everything went well except for a failsafe when I went up really high, but I luckily was able to reconnect in time and continue the flight. I was getting "RF signal low" warnings when I shouldn't have, but I think that was because I had dynamic power turned on and the 868MHz on instead of 915MHz. I have since switched those features to off and 915MHz, but when I plugged in a battery today to do some configuring in Betaflight my crossfire nano was giving me a solid red light and seemed to have lost its bind to my radio. It bound perfectly when I did my first bind and I was able to update the firmware on the receive

SOLVED -

Yesterday I flew two packs on my maiden flight with a new build. Everything went well except for a failsafe when I went up really high, but I luckily was able to reconnect in time and continue the flight. I was getting "RF signal low" warnings when I shouldn't have, but I think that was because I had dynamic power turned on and the 868MHz on instead of 915MHz. I have since switched those features to off and 915MHz, but when I plugged in a battery today to do some configuring in Betaflight my crossfire nano was giving me a solid red light and seemed to have lost its bind to my radio. It bound perfectly when I did my first bind and I was able to update the firmware on the receiver as

I am new to minimalist shoes, but I would really like to try them out and I am not sure where to start. I would like to be able to find a pair that works well for hiking trails as well as running on pavement. I have a wide foot and I typically have to pick shoes that are either 2E or 4E. Does anyone have any recommendations for me? Thanks!