ChargePositive

Hi all!

Just got into Ollama relatively recently. I have it installed on a couple machines:

1. My Home Server

• I3-10100
• No GPU
• Running Ubuntu
• 32 GB RAM
• Ollama typically running llama3.1 8B

2. Gaming PC

• Not 24/7 server
• Running on WSL on Windows
• 32 GB Ram
• 3700X
• GTX 1080
• Ollama typically running llama3.1 8B

I run Ollama through Openwebui on both instances. The home server is expectedly much slower, but is not terrible once it actually starts generating a response. However, I have custom models that have a lot of documents as their "knowledge", and that is where the home server becomes unreliable, often timing out before responding.

My gaming PC is actually really qu

Hi all,

I am trying to access a service (Ollama) using WSL2 over LAN and it is not reachable. I enabled "mirrored" network mode in the ".wslconfig" file and it clittered up my network adapters page in WSL but otherwise did not solve my problem.

My local IP of the Windows Host Machine is: 192.168.1.15

The output of "ip a" in WSL:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet  scope host lo
       valid_lft forever preferred_lft forever
    inet 10.255.255.254/32 brd 10.255.255.254 scope global lo
       valid_lft forever preferred_

Hey all,

I want to try running my own AI instance for fun and am having an issue.

I am doing this install by a VPN on my windows computer to remote server running Ubuntu to run Ollama. I run the curl command on the Ollama website and it runs fine:

>>> Creating ollama user...
>>> Adding ollama user to render group...
>>> Adding ollama user to video group...
>>> Adding current user to ollama group...
>>> Creating ollama systemd service...
>>> Enabling and starting ollama service...
Created symlink /etc/systemd/system/default.target.wants/ollama.service → /etc/systemd/system/ollama.service.
>>> The Ollama API is now available at 127.0.0.1:11434.
>>> Instal

Car: 2017 Chevrolet Sonic

Hi all,

A piece of metal is lodged into my tire and I am not sure what the best path of action is. Here are the details:

• Metal in rear passenger side tire

• Front tires have much lower (not yet needed to replace)

• Rear tires still have a lot of tread

​

So, I know the metal is lodged into the non-repairable part of the tire, so I need a new one. The problem is I can't find replacements of the tires I have now, Continental DWS 06 (225/40/18), only the new "Continental DWS 06 PLUS, which has traction and compound differences to what I have now. It would be nice to replace just the one, and rotate the rears to the front, but

Car: 2017 Chevrolet Sonic

Hi all,

A piece of metal is lodged into my tire and I am not sure what the best path of action is. Here are the details:

• Metal in rear passenger side tire
• Front tires have much lower (not yet needed to replace)
• Rear tires still have a lot of tread

So, I know the metal is lodged into the non-repairable part of the tire, so I need a new one. The problem is I can't find replacements of the tires I have now, Continental DWS 06 (225/40/18), only the new "Continental DWS 06 PLUS, which has traction and compound differences to what I have now. It would be nice to replace just the one, and rotate the rears to the front, but then I would have a mismatch of tire on

Hi all,

I understand that what I am asking here may be a bit niche, but I am just looking for some ideas. I made a post on this sub a few days ago regarding methods of getting smart home control to a garage ~650 ft away from my apartment. My current path is to get two point to point WiFi units, to act as an access point. This should give me the range to the garage. However, I would like to avoid using WiFi for a contact sensor I want. Is there any (cheap) way to send a Z-Wave to Zigbee signal through this wifi connection to HA?

If not I'm thinking I'll settle with a non-local control wifi sensor, or if I want to spend the money I can set up another HA instance to control that with the re

Hi all,

Just moved into a new apartment complex, and Have a detached garage that I would like to attempt to make smart. The issue is, the garage is about 650 ft away from my apartment. I am on the third floor and there aren't many obstacles but from what I've seen, Z-Wave (seems to go the farthest out of zigbee and wifi), only has an open air range of about 300 ft. I have seen some repeaters that claim 400 ft, so I am wondering if having one at my apartment and one at my garage would give me the "combined" reach of 800 ft, or maybe it doesn't work this way?

Any recommendations on what you would do to solve this range problem would be appreciated!

Thanks

Hi all,

Might be a silly question but the topic came up at work today and I realized every analog device I've worked with until now had readings that went up only one digit at a time (i.e. 1,2,3 or 1.1,1.2,1.3, etc.). However, we have a rotameter that has every 0.5 denoted. So the readings are 0.5, 1.0, 1.5, 2.0, and so on. With normal instruments I would always just add a significant figure and estimate in between the lines. However, that doesn't apply with this type of markings.

Say you had a reading that was halfway between the markings 7.0 and 7.5, what would that be recorded as? 7.3?

Need this clarified as it is bothering me,

Thanks!

Hi all,

I have tried to download a website for my car using httrack and a few online tools but all of them were imperfect, usually missing the pictures. I pretty much never download websites so not too worried on learning how to do it. Could someone either download it for me (big ask) or point me in the right direction to do it myself?

Website: https://www.cadillac.com/sedans/preceding-year/ct4-v-blackwing

Thanks!