ChoKoth

So it appears that the app installed to my D:, however the launcher itself still puts everything in the %appdata% folder. The whole point of installing to the new location was to conserve drive space. I've found where to change this, but do I seriously need to go through each option one at a time and change the location it points to instead of it moving everything to it's installation directory?

I'm using a Photon Mono 4 Ultra, and I'm wondering what most people using ACF are seeing for lifespan on their films? It's not unusual for my film to develop obvious weak spots within 3 or 4 prints, and often start leaking in under 10 prints. Is this normal, or am I doing something wrong?

I'm using the stock vat, and the re-installed films provided by AnyCubic.

I'm trying to flash MriscroC firmware to the printer, but I can't get it to take. I think I have a good build, but the printer won't take it.

I'm running the Creality Touchscreen (DWIN, I think?) that came with it. I've tried putting the firmware in the root of the SDcard and in the STM32F4_UPDATE folder, the latter of which works for getting stock firmware back on the printer when this fails. Neither has made a difference.

I can flash the screen without issues. Does anyone have a guess what I might be doing wrong here?

As far as the firmware itself, I used Mriscroc's settings, and only changed the items that showed up in a diff between the s1 config, and the default s1 condfig from Crea

Right now my lead contenders are the SV06 ACE PLUS and the SV07 PLUS. I have a few prints that I need the bigger print bed, so at least 300mm is required.

My question is about reliability. Right now I have 2 hand-me-down Ender 3s (V2 and an S1 PLUS), and I'm fighting with them constantly to try to get them to print. I think the V2 is just about to be declared dead, and the S1 is going to need a bunch of work to get the bed to a leveled state as it's currently warped.

Anyway, that backstory leads to my question: I want a printer with a large build volume that just works, and works reliably. I don't mind a little tinkering, but I'll be honest, I have probably gotten WAY more than my yearly q

A little context, sorry, it's a little long.

I picked up this v2 from a coworker that was tired of fighting with it and said I could "just take it". I'm starting to think free was too much to pay for it. It's a V2 with a sprite Extruder, a CR Touch, and a DWIN display. I'm new to actually doing 3d printing, though I've been dabbling in reading about it for about a year. I'm controlling my printer mostly through Octoprint.

When I got the printer I was having issues with the extruder just stopping after 2 or 3 print attempts. The printer has a glass bed, and ABL was reporting a .3 mm drop on the right side of the bed all the way across. When I turned the bed 90 degrees, it magically went a

Just started my anual re-read of the series in prep for the next book. I'm on Fool Moon. It's HEAVILY implied that Tara West is carrying MacFinn's child.

The curse says his line won't die until the end of days, In his conversation with Dresden in Wolf Park he mentions "other reasons" besides having a huge range while looking pointedly at Tara, I'm sure there will be other references as well, but I'm still early in the book.

Anyway, I'm curious if this has ever been brought up to Jim, if he's said anything about the young Wolf-were appearing later in the series (likely the end trilogy, or perhaps the hinted at Kaiju or wrestling books).

The "end of days" comment kind of implies that his k

So I'm trying to get an MCP order for a bunch of the theros beyond death full art lands. I would prefer not to have to scroll through on 100 copies of each land and manually select the correct printing for each. I'm having a hell of a time finding how to select the specific edition for the cards on the initial page, though.

Anyone familiar with this have any pointers for me?

I added space to the disk that OpenBSD was using, and would like to use that in my /var partition.

Of course that space is now located at the end of my drive, and I'm not familiar enough with how disks work in openBSD to be able to rearrange everything to get that space to the end of the same partition /var is on. Output of df -h and a fdisk print Follows:

# df -h

Filesystem Size Used Avail Capacity Mounted on

/dev/sd0a 1005M 76.3M 878M 8% /

/dev/sd0k 19.1G 78.0K 18.1G 0% /home

/dev/sd0d 3.2G 10.0K 3.1G 0% /tmp

/dev/sd0f 2.9G 1.3G 1.5G 46% /usr

`/dev/sd0g 1005M 332M 622M 35% /usr

FIXED - though I'm not sure how. Read my reply below for vaguely helpful ideas.

I can't get VS code to load any of my cmdlets to while I'm working.

I can get PowerShell to run them no issues, but not the PowerShell integrated console in VS code.

Everything is stored in my modules folder, I'm running as the correct user, and the damned things work in PowerShell. There is some option in VS code that I'm missing to allow it to load the modules, but I've been all the way through the settings for VS code and the extension itself, and it won't load them.

This has worked previously, even in the last few days. I'm not sure what would have changed in that time or I would be running up that tree.

I picked up my Alpha about a year ago, and I have been looking for somewhere to buy an optics plate, and maybe a holster for it since I got it. I found a decent holster, though if I'm not careful it will trigger the raised mag release when I draw.

I was wondering if anyone here had a recommendation of somewhere to get accessories. Preferably at a good price, but I'm getting pretty desperate.

Marked as spoilers since a discussion about this could easily bring up major points from Battle Ground

Winter Court?

White Court?

White Council?

There has to be a better way to refer to these groups, especially considering how deeply involved Harry is in all three at this point.

They're too long to type all the way out every time you want to reference them, but I can't come up with a way to unambiguously shorten them.

I was going to suggest the first three letters, followed by the first 2 (WhiCo). Except even that doesn't work.

Anyone have any suggestions?

Every page I go to includes promotional material for home lenders. While that's all fine an good, I can't trust any recommendations given with monetary gain from the advisor. I was wondering if anyone knew of a good place to start searching for a lender that didn't feel like someone saying, "These guys are great, and they only gave me a little money to say so."

So my imperial rank mission required a medium sized ship. I swapped to my smaller ship so I could pick it up and run it later. Not thinking, I picked up a bunch of delivery missions.

Having cleared the mission boards, I swapped back to my 'Conda, and started filling my cargo bay. I now sit with a full cargobay (384 units) that are haulage to two seperate outposts.

​

Is there anyway to return this cargo to the mission giver so I can swap to my smaller ship and run this the way I was supposed to, or am I going to end up Jettisoning cargo and partial completing the mission?

So I'm building an alternate history urban fantasy world set in the old west. I would like to get some maps of territories of the period and modify them for my purposes, however I'm having a heck of a time finding any of decent resolution. Does anyone know know of a good site that might be a repository of something like that this I could work with.