DevPump

I have a Mars 4 Ultra that I am looking to put in my attached garage. I have an grow tent that will hold that printer and a wash/cure station. I also have a heater setup in the tent. The printer has the USB air filters from elegoo.

The garage door would be closed, does not have any windows and also has an AC air handler. if I put the setup more than 10-15 feet away do I need to worry about the fumes making it into the air handler? Any suggestions on how to make this better?

I just did all the wiring on my 5 card rig preparing to add 2 new cards. I'm not quite sure why the card's fan just stopped but it no longer runs while all the other fans are running just fine. The card itself appears to function just not the fan.

I have tried swapping the riser with known working riser, that did not make a difference as well as swapping PCI-E slots but no luck.

One odd thing to note is the claymore 11.0 is reporting a fan speed of 60% while the fan is idle.

I plan to move the single card to another system for testing tomorrow to see if there is a system specific problem as well.

GPU0 t=56C fan=60%, GPU1 t=89C fan=60%, GPU2 t=60C fan=60%, GPU3 t=48C fan=60%, GPU4 t=55C f

I want to assume this would brick the card.

Does anyone have experience with updating a H310 (crossflashed to SAS9211-8i) via the Lifecycle controller?

The Current Version is blank (00.00.00.00) and the available version is 07.03.06.00

Hello DataHoarder,

I just flashed a DELL H310 using this guide (Thanks u/techmattr)

The card works in all other PCIe slots but not the internal storage slot.

With a Dell R710, the following issue occurs:

I receive the error: "Invalid PCIe card found in the Internal Storage slot System halted!" when using the internal storage slot.

The firmware currently on the card is: 2118it.bin

I do not have a Mini or Mini Mono.

Is something missing from this guide or did I miss read?

Steps used:

H310 DOS:

megacli.exe -AdpAllInfo -aAll -page 20

megarec.exe -write

I am looking for a similar configuration below for GNU+Linux. Does anyone know of a way to do this?

On FreeBSD, add these lines to /boot/loader.conf:

hw.mfi.allow_cam_disk_passthrough=1
mfip_load="YES"

If necessary, destroy any volumes you've already created (you can use mfiutil for this) and reboot. You will then have direct access devices (da0 etc.) for each of the drives attached to the PERC 6/i.

Reference

Hello all,

I have 2006 Ford Freestyle 3.0 that has just recently went into Failsafe mode.

The engine sounds and appears to work fine other than not being able to accelerate.

The following codes were given: P0701 P2104

I have tried cleaning and replacing the throttle body twice. (once myself and once by Bartow Ford) the negitive terminal had been left off the battery for a few minutes to reset the codes.

Problems still persist. Any ideas would be appreciated.

Hello r/zfs,

I have Dell PowerEdge 1950 with a PERC 6/I RAID controller. From what I have read this RAID controller does not have a JBOD or HBA Mode.

Would it be beneficial to setup each of the 4 drives in a 1 drive raid 0 per disk?

Any suggestions would be appreciated.

I plan to use one of the following for the Operating System: Centos Root-On-ZFS, FreeBSD, or FreeNAS.

Thanks

Does anyone know of a Distribution that is a good cross between Gentoo and Arch Linux.

I really like both, but the feature split makes it rather hard to choose between them. I am currently on Gentoo with all of my systems, but I occasionally want the Bleeding edge packages that Gentoo does have as well as the AUR. I want to only run rolling distributions.

I have tried Manjaro and Sabayon, but the both lack something from Gentoo and Arch.

Has anyone had success with using a tmpfs for '/var/tmp/portage/' while using SELinux configured as enforcing?