DiggingforPoon

Welp gents, it has been a splendid run, but as of today I am officially out.

Game crashes (Unreal Engine) are killing me, and I have a non-inconsequentially powered gaming PC that has no other game stability and/or crashing issues (e.g. Metal Gear Solid Delta: Snake Eater and Borderlands 4 both run fine, both are UE5).

I will miss my care-bear lobbies and the fun, but I can't deal with losing gear and loot to crashes, not ARC or players.

So Long, and Thanks for All the Fish!

With the new remote work allowance officially allowed, I was hoping to settle in for a few years quietly in the outskirts of Hamilton to the NE, but might be hard if I have to leave for regularly for extended periods.

From what I can gather a Visitor Visa lasts 9 mos (single entry) and I can extend it (possibly) another 3mos, but then, no matter what, I have to leave the country for 6 mos before I can get another one.

Is this true?

I am on an American passport, am also on the Tier 1 Green List (either as ANZSCO 135111 or as ANZSCO 262112), not planning on working locally, but am 50 years old.

Whether I scan the QR code or use Bluetooth, I get an error immediately that says;

Kind Reminder

The device is not registered in the open platform.

And I cannot do anything further. Any ideas?

After being down for anywhere from 2 months to 3 weeks, the 13 panels the were down came back online as of 8/9 @2:25PM PDT, with no rhyme or reason...

I really wish I could understand why they were down in the first place and how they came back.

As times passes, I am slowly getting messages stating that I have more and more panels either in "temporarily not producing any power" or "This panel has stopped working" status mode.

SunPower said they were going to do something remotely that was supposed to take effect by Tuesday, but still have 13 panels in these states, and with the news, I am hoping I can support this as much as possibly locally.

Is there any way for me to do anything on my side? I have 49 (Forty-Nine) M425-H-AC panels connected to a SV-HUB-01-C with 26kWh of SunVault Storage (2 boxes)

I have an "older" light industrial workshop I recently acquired and it has a 400 amp 208V 3 Phase Delta panel with no Neutral feed, just 3 hots and a Ground. I have a variety of 120V Single phase, 240V Single Phase and 208V 3 phase equipment I want to run, so assuming I get the equipment plotted out for where I want outlets and the load that will be on each circuit, what ELSE needs to be done?

How do I get Single Phase without the Neutral?

Caveat, I understand my knowledge of electrical is lacking, which is why I will not do the work, but I do want to understand. I will be hiring a qualified pro with insurance to do this.

I was wondering if anyone makes 96V (nominal) packs, say 40aH? Or would I just be better off getting two of these for my Death trike?

Looking to lease a small (800-1200 sq ft) workshop that I can setup and do some light woodworking, electronics, glass blowing, welding, etc... for personal use. Closest I can find something like this seems to be Woodland Hills/Chatsworth or Camarillo.

With luck, looking for something that I will keep for most likely about 20 years or so.

Any suggestions, tips, reccomendations?

I want to add this Steam generator to my bathroom remodel, but before I even mention it to my contractor I want to get some outside, expert opinions.

It says it is a 208V-240V 110Amp (max).

I have a 200 Amp residential panel that is currently full, and as an added kicker, it is a all tied into a SunPower Solar system with battery's.

What would be the best way to add this, TO CODE, in southern California.

Anyone having issues getting insurance due to them not being able to find any details on your VIN?

Both Geico (whom I already use) and Progressive can't find my VIN (which statrts with LB2S) when they try to look it up.

Order #1079, Jan 14, 2021 Delivered 145PM, Nov 19 2022

Driver was a total asshole (Hey John from Haul Bikes), I learned @ noon they were coming at 130 and the driver was PISSED that I was picking my son up at that moment 10 minutes away. I was told "You have been the hardest customer to reach, you are a hundred miles out of my way, I have been calling you non stop"

Got home at 137PM, driver never even showed until 145PM...

Aside, from that, no issues with the bike itself. My charger and title, BOS and such came via FedEx earlier the same day

My son managed to crack the front rim of his RadRunner Plus. Where can I get a replacement Rim that is both compatible and aesthetically similar?

Thank you in advance for any assistance.

I am looking for someone to give my KWA Vector that I recently purchased a good once over and make sure it is in top shape mechanically, and if not, fix and replace whatever needs it, correctly. I am located in SoCal (91377), so Local is nice, but expertise is preferred.

Anyone know of someone they recommend?

Looking for a KWA Kriss Vector GBBR, prefer original boxing and accessories. Prefer Black, but will consider Tan.

Reasonable offers will be entertained seriously.