GoFastEatTrash

u/GoFastEatTrash



r/fosscad•

Howdy y'all.
I've been printing more PA6-CF and PAHT-CF recently, and want to figure out a better system for annealing. As of now, I have tried annealing in an old toaster, my kitchen oven, and on the print bed. None of these options are great, primarily due to the lack of control and fluctuations with the temperature. I have been surrounding parts with fine grit glass media, which has helped a bit, but still isnt ideal.

Anyway, does anyone have any specific recommendations for toaster ovens, air fryers, food dehydrators, etc? Ideally i'd get something with PID control, but I'm also looking to keep the cost down.

Thanks!

330


r/NightVision•

Howdy. I wanted to see if anyone had updated their ST6 monocular to anything other than the v1.0 firmware that it came with. Anyone know if the devs plan to release anything else? I know that the ST6 is very similar to other monocular options out there. Does anyone know if there’s firmware compatibility with those models? Cheers!

10


r/fosscad•

Howdy.
I like to be able to print on my Bambu X1E without worry of the print history (gcode, metadata, previews, etc) being accessible by anyone.
My printer is currently connected to WLAN and fully integrated with Bambu Lab's servers. My understanding is that if I were to disconnect it from WLAN, print off of a micro SD card, and enable the printer's "incognito mode", that would allow me to print privately, and securely.

Is that an accurate assumption? Are there any flaws in this? Anything else y'all would do? Thank you for your input!

30

r/AeroPrecision•

Howdy.

I am looking at switching the upper receiver and handguard on my SPR build. I am keen to get the M4e1 upper because I would like to reduce pressure on the barrel nut and barrel when I am shooting off a bipod. I noticed some serious difference in impact when shooting from a bipod vs shooting off my shooting bag. I would like a handguard with arca rail.

I am looking at something like this. Does anyone see any reason that this wouldnt be a good option? Anyone see any better options? Thanks!

811

r/RTLSDR•

Howdy! I am trying to put together a better software/software configuration solution to do an RF area study. I would like to do wideband, longer term (span of hours) scans of my neighborhood in the 2m range for fun.

I have tried the frequency manager + scanner plugin for SDR# as well as RTL Power. I am struggling to adapt both of these to my use case and am hoping for some insight from yall if anyone has thoughts.

SDR# and the FM suite is great, but the scan seems to be a bit course in its step sizes. I can’t seem to adjust this anywhere, unless I’m missing it.

RTLpower is cool, but I can’t seem to find a way to output the saved frequencies anywhere. Am I missing something with this as

25

r/NightVision•

Howdy.
I have been looking more seriously into getting a thermal unit in the last few months and wanted to get some input from y'all that are more knowledgeable and experienced with the current market options.

Use Case: The priority of this unit will be for spotting/scanning in the field. Having something that could be clipped onto a 5.56 carbine would be nice. I dont anticipate mounting it to a helmet, but that of course would be a nice to have. I have a PVS-14 so this would be used in conjunction with it of course. I am looking for 640p, and trying to prioritize detection distance. 50Hz would be ideal too of course.

Budget: Trying to keep it around $3,000. Ideally would buy somethin

36


r/Thermal•

Howdy -

I have been inspired by a certain engineer on Instagram who is working on a very cool DIY thermal monocular project. It looks very cool but I dont want to wait for him to release the project guide; I would like to start experimenting myself now.

This post asked a similar question but the opinions about the hardware in question seemed to be inconclusive.

So - Does anyone have any experience with that tier ($500-$1000ish) of thermal cameras/cores? Id love to cobble something together. Thanks a bunch!

20

r/androidtablets•

Howdy. I was hoping for some advice on a future purchase that I am weighing out. I am looking for a tablet that will be used for field work. Water resistance, drop protection, battery capacity and screen brightness are the most important considerations. Secondary considerations are performance and expandable storage. Camera quality and audio quality are entirely unimportant. If possible, I would like for the tablet to NOT have any cellular capabilities.

I am hoping to keep it below $300 or so and am okay buying used. I was thinking about a Pixel tablet (so i can flash it with Graphene), but the lack of any weatherproofing is too much of a downside I think.

Thanks for any suggestions!

21

r/ATAK•

Howdy. I use Meshtastic and ATAK together regularly. It is fun to push the boundaries of LoRa and experiment. In the last few months I have been inundated with BearTooth’s targeted advertising and paid content on YouTube. I have no interest in buying their package but I’m very interested in the hardware and its capabilities. After a bit of research i had a few remaining questions in case anyone knows the answers.

  1. Does anyone know what radio protocol they use? Obviously it’s ISM, and I assume the mk1 was just a derivative of Meshtastic, but I can’t find anything specific about their mk2 line.
  2. What transceiver / radio module are they using? All I can find is that it’s 1W.
  3. Does an
721