ImLagging

u/ImLagging


r/Makita•

I just picked up my first XGT battery and charged it right away. It’s a 4ah model that I bought from Home Depot. I don’t remember what the pre charging voltage was, but it was pretty low which I expected. A few hours after the charging was done, I tested it with a multimeter and it’s sitting at 30V. I would have expected it to be at least at 40V if not higher. My LXT battery that had been sitting for weeks after charging is measuring over 20V.

Is something wrong with this XGT battery? Or are they really 30V?

48

r/WLED•

Hey everyone. I’m looking to install LED’s on 3 sides of the house and I’m getting some inconsistent info on if what I’m planning is do-able. I was hoping some of you smart people can either confirm what I’m thinking or smarten me up if I’m off base. I have not done a set up of this scale, so I’m posting here before I start buying stuff.

Here’s what I’ve planned out so far:

  • Controller: Dig-Octa brainboard with Power 5-HV
  • Power Supply: Meanwell LRS-600-48
  • LED lights: Currently I’m looking at using WS2805 IC RGBCCT 60 LED’s per meter, either 12V or 24V - I’m still on the fence on which one will be best. Which LED’s I go with is still subject to change as I’ve gone back and forth betwe
512

r/prusa3d•

Core One+ assembly question

Question/Need help

Hello everyone. I’m currently assembling my Core One+ and so far it’s been going well. No real issues and I’ve been enjoying the process. But I do have one question and was wondering if anyone else experienced the same thing I am.

On page 95 of the assembly guide, step 18 where you secure in the screw to secure the 2 pulleys to the XY motor mount right, it seems as if there is absolutely zero resistance once the screw reaches the plastic. I do get some resistance on the left motor mount so I know I’m good. I ordered a replacement part and noticed the exact same issue, absolutely zero resistance.

Is this something I should be concerned with? Will this cause any issues while using the prin

26


r/Makita•

I’ve been thinking about picking up an Impact Wrench for when I work on my car. Is it worth spending a bit more money on the XGT Impact Wrench vs the LXT version? I currently have a good many LXT tools and over 10 LXT batteries. So I can just buy the tool only. But I don’t have any XGT tools nor batteries as of yet so I’ll have to spend a bit more to get batteries. Does an impact wrench benefit from 40V over 18V? There’s been a few times when I’ve needed one and I didn’t have enough room for a long handled breaker bar. I did try my Impact Driver, but it wasn’t powerful enough (the one time I was able to try it).

The other reason I’m thinking about going with the XGT version, is I’ve also b

10

r/woodworking•

Let’s say you have a $600 gift card. The big box home improvement store that the gift card is from has a few bench top jointers that I’m looking at. I know there’s limitations for bench top models, but I don’t have space in the garage for a floor model unless I want to park outside. If I need to do longer boards, I’ll probably make some infeed/outfeed extensions.

Of the options with the price range of the gift card, I was looking at getting a one larger than 6” and hopefully a spiral cutting head. I see the 2 following ones seem to fit that criteria.

  • WEN 8” 10amp, $406
  • WEN 10” 12amp, $589
  • Grizzly Industrial 8” 10amp, $595

There are cheaper ones, but they’re all 6”. There is a Jet

10

r/Ubiquiti•

Last night there was some power related issues where my UPS was switching between battery and mains power very regularly (basically every second). 3 of 4 UPS's were doing this, plus lights were flickering multiple times per second. Ultimately, I shut off the UPS's as the batteries kept draining and had no chance to recharge. Plus, I didn't think this was good for the longevity of the UPS's in general. As a result, that meant my whole network was offline for the night. The light flickering got worse as the night went on and even worse this morning. Then the power went out this morning. The power company made an automated call to let us know they were working on some equipment. After t

12

r/homeassistant•

I’m looking for a few temperature and humidity sensors that meet the criteria below. Any suggestions are welcome. I have a SkyConnect and a Zooz 800.

  • Should be either Zigbee, Zwave or Matter based (I might consider esphome based sensors if nothing else fits, but I’m not currently ready to set up any such devices)
  • Uses a AA, AAA or CR123. I’d like to use rechargeable batteries and most sensors I’ve seen seem to use button cells. I have some RCR123’s.
  • I don’t need a screen on the sensor itself, but I would consider it. I would prefer to not change it he batteries every 2 or 3 months, so if a screen reduces battery life, I’d rather veto e without a screen.
  • No other hub, login, accou
14

r/cycling•

I’m looking to buy a bike and I’m wondering if a gravel bike is worth the extra cost over a mountain bike. I live in a relatively flat area, definitely no mountains. I’ll be riding on paved surfaces initially, since I’ll be riding with the little one who’s currently too young for anything else. But once they are able to handle trails, I’ll start riding there. Even then, I won’t be doing any difficult trails. So it seems like a gravel bike is the way to go. However, they seem to be twice the cost of a mountain bike.

Does it make sense to spend around $1,500 on a gravel bike when I can get a mountain bike for around $600? Is there a reason gravel bikes are so much more expensive?

319

r/IKEA•

I have some Besta’s that I would like to mount to the wall using IKEA’s Suspension Rails and I would like them to be as high up as possible (it’s a low ceiling, so there won’t be any issues of trying to reach anything, I can’t stretch my arms fully up due to how low it is and I’m not much taller than average). I know that with the Suspension Rails, I need to have some clearance to mount the Besta. My question is how much clearance is needed? I’ll cover any gap between the Besta and the ceiling with some kind of molding (or some other similar ideas).

14