Lagrange91

I have some Dmt from a prior extraction which I would like to purify. So far I read the easiest way would be to do a re-x with a water wash is that correct? I already did a re-x with another batch some time ago. Quite some part of the batch didn’t fully redissolve and gathered at the bottom. How to proceed with that part? I think there is quite some Dmt in there and would not like to waste that. At that stage would these residual crumps be safe for use already or has it to be further cleaned in some way? And can someone tell me approximately how much nps I should be using per gram of Dmt for the re-x? Thanks a lot!

Hello, I am interested in a clean setup and would love to have a dock with power delivery (100W+) to connect to all my peripherals using one thunderbolt 4 cable.

Host device: M1 Mac (2021) with thunderbolt 4

I would love to connect via dock to:

• DQHD 5120x1440 @ 120Hz (equivalent 4k @ 120Hz) monitor (display port)
• mouse
• keyboard
• webcam
• potential optional stuff

I really searched a lot but I wasn't able to find a final answer wether one tb4 cable is capable of handling this all together. I am able to drive my monitor directly with a tb4 to display port cable. I would be happy if someone could tell me if my requirements exceed the capabilities of a single tb4 cable. If not I would

I wanted to ask if it is sufficient for a 5 meter ws2812b strip with 60 leds/m to have a power injection at the beginning and at the end? Would be nice to hear your advice / experience.

Due to a recent incident I experienced where the bottom of a glass beaker broke off (luckily during the acid phase, a big mess nonetheless) I want to expand my knowledge regarding the proper use of glassware. So if you have some best practices you can share I would be very happy. Furthermore I now bought more expensive quality glass beaker (Schott Duran). Reading deeper into their specs I found some guidelines. It is written that the Temperatur for long heating periods should not be above 350deg C. Though for short spans one might go up to 500deg C. But the maximum temperature difference between two points of the beaker should not be bigger than 100deg C. My heated stirrer allows to set the

I slowly increased the amount of bark I used in my teks. I successfully extracted from 250g MHRB with a yield of ca. 3g which I was content with. So in my last extraction I wanted to scale up to 500g MHRB (380g from the same batch, 120g from a new batch but same vendor). The yield was again around 3g so I’m wondering what might have been the problem. I hope you can help me find it. I will sum up what I did in the several steps extracting from 250/500g. If you need more detailed information I have them in my lab documentation. I’m using a heated stirrer so when I heat something I watch for the mix to be stirring such that nothing settles.

Acid stage: 250g: 1l water, 300ml vinegar, resul

I’m thinking of buying a Ccell palm with a Th2 since a lot of people here seem convinced by it. Could you tell me about your experiences with it? I was just wondering because with my fireluke twister I’m able to control the wattage and therefore the strength of the vapor. It works really well but I like the style and the size of the palm as well as that the cartridge consists only of ceramic, metal and glass. So the setting the palm is running with by default is already a good setting to vape dmt? What are other advantages/disadvantages or important things to mention? Thanks

What is an environmental friendly way to dispose used solvent (I reuse solvent used for pulling but I want to dispose the solvent for defatting)? Thanks

Before adding salt and naoh I want to reduce my acidic solution to a volume which is easier to handle. Is the DMT in that step sensible to heat? I’m just wondering if I can just boil the solution down without loosing DMT or if I have to stay below a certain temperature. Thanks

I wanted to ask how critical the purity of the Naoh is. It is written that it should be 100%. But in the web I find mostly purities in the range from 98-99.5%. Is that an acceptable purity or should I skip these? Are there recommendations what brands to buy in Europe/Germany? Thanks for the help.

Hey fellow jugglers, could you give me some advice or experiences on LED balls? I would like to get some long living high quality ones. In other discussions I read a lot about the k8 balls. I’m considering them but since they are an investment I would like to hear some opinions. Or are there good alternatives? Has it been long that they have been reworked (not that I’m gonna buy them and short time after they bring a new version)? Thanks for all your input.