R0factor
u/R0factor
I have the budget and more importantly spousal approval to install a soundproof studio in the unfinished portion of our basement. This will be a DIY project and I have decades of experience framing walls, hanging drywall, running & installing electrical, etc. I've built soundproof barriers before with double-layer 5/8 drywall, decoupled framing, etc, but this will be my first formal room-within-a-room construction. Total area will be about 350 sq.ft, and I have plans for ventilation, doorways, lighting, as well as sound treatment once its done.
If you've done this, what did you learn in the process? Anything that needed more attention, or other areas where you went unnecessarily overb
I'm getting ready for my 3rd DIY install. In my previous Subarus there was always room under the passenger seat for an amp but in the current Highlander generation there's ducting for the rear passengers taking up that space.
For the amp I'm thinking of something like a Kenwood Excelon x803-5, or something similar if anyone has suggestions. That Kenwood is about 10x7x2".
Is mounting it in the rear storage compartment an option? I've seen people on YT mount it there but not sure about the ventilation. I live in the northeast which gets hot during the summer.
Any other clever locations? Can these go under the sliding rear seats?
For those of you familiar with this town, could you legitimately call it suburban? I referred to it as rural in the report since it’s almost 300 miles from Boston which is the nearest legitimately “urban” center in the region. This is a situation where the lender won’t approve the loan if the location is considered rural.
General facts: Bar Harbor is a coastal town in the downeast region of Maine, adjacent to Acadia national Park. It has a population of about 5000 people living there year-round, but is a very popular summer tourist destination. The subject is located within walking distance to the town village and is on public water and sewer. The nearest city is Bangor located about 50
Noob-ish question... When you're boosting something like 60hz for extra oomph on the kick or 200hz for a snare fundamental, or 2k+ for the attack, how do you typically handle the Q value? Like does the 60hz bump extend from 57 to 63, or 40 to 80hz? Same question for boosting on the bass guitar.
I know the general answers are "use your ears" and "it depends on the mix", I'm just wondering how it ends up being handled most commonly.
Bonus question... what's the consensus on compressing low/sub end? I've seen some people here say they never compress anything under 80hz.
Non-pro here... My band records remotely and sends me DI tracks for guitar & bass and I'm wondering how to get the most out of the amp & cab modelers in Amplitube 5. I recently learned about the importance of setting the proper input gain to work with the gain structure of the modelers which has helped. But I'm still getting a very hot & crunchy sound and sometimes a whistling sound will show up in the 2-4khz range when the signal gets saturated. Is it normal to have to EQ these out either before or after the plugin? Or any other methods to counteract the harshness? Is the sample rate important... 44.1 vs 48hkz? Or are my bandmates tracking their DI stuff incorrectly?
Also specifically
Location: NH - My ex and I have now both remarried and I'm curious how child support is calculated at this point. Is it still by individual income or is it combined household income for each couple?
According to the Google AI answer it's based on household income but I can't find the exact law/statute it's referencing.
Major bucket list moment for a drummer dad… your daughter’s high school calls you to fill in last minute* for their Rock of Ages musical, and you get to watch her perform from the on-stage pit…
reddit.com/gallery/1s0eolz
reddit.comOur theater area is on the smaller side and has a narrow pathway placing the right surround speaker in danger of getting bumped into. Right now I’m using older Polk dipoles mounted above shoulder-level, but I wanted to possibly mount something at ear level that’s either in-wall or a relatively shallow wall mount.
Any suggestions? For reference my LRC are Energy C5s, and I also have Polk OWM3 for rear surrounds in addition to the dipoles. And the replacements don’t need to be dipole.
Crack formed in older but barely used Hydraulic head. Does the oil degrade the plastic?
reddit.com/gallery/1rhgxmy
reddit.comI have a home theater setup based on my speakers from the early 2000s, Energy Connoisseur C5 fronts, C-C1 center, and a Klipsch RW-10 sub. I have a dedicated windowless room (+/- 14' x 20') in my basement we're now using as a theater that I will be continuing to treat for better sound. And I'm planning to upgrade the AVR to something like a Denon 3800H since my old Yamaha lacks 4K/ARC/Atmos capabilities.
Roughly how much am I looking at for a worthwhile upgrade from these speakers, and what models should I look into? There's nothing wrong with them, but after upgrading my old studio reference monitors for mixing music it's obvious that speaker performance has jumped up in the past 2+ decad
My marching bass conversion project turned into an excuse to rewrap the whole kit in Charcoal Pearl. Super stoked but yikes this was a lot of work. More in comments...
reddit.com/gallery/1r4ulco
reddit.comGetting back into a proper home theater setup now that I have a dedicated space again and noticed on Netflix and Disney+ nothing is really being sent to the rear surrounds despite my receiver showing those channels are operational watching most newer movies and shows, and the internal tests confirm I have everything wired correctly. It's an older receiver (Yamaha RX-V1900) getting signal via a toslink/fiber optic from the TV (TCL QM6K) since the receiver can't do ARC. I'm streaming through a Roku Ultra. Thanks for any help!


