RandomCanadianMan

Purchased an adidas authentic pro jersey from nhlshop.com at the end of October. Received it today and was surprised it didn’t have a C on it!

I see the Ottawa team shop site has a jersey with a heat pressed C, but it was way more expensive for what I can tell to be the same jersey. NHL Shop was 25% off ($190).

Is this normal?!? Are all the C’s heat pressed?

Hello,

Have been struggling with this problem a while now and hoping a fresh set of eyes will help me out. I have a table with time entry data and am trying to group together records that are in continuous date ranges, allowing for weekends in between (so can be up to a 3 day gap).

​

Here is an example of the table:

https://preview.redd.it/7wm2z2un7xh91.png?width=250&format=png&auto=webp&s=069e88d18698d6d32c4adcc58751a77d328f4277

So given the above, for user 1 I would want to group together 2022-01-05 => 2022-01-10, but 2022-01-15 should be a separate group.

Below is what I have tried so far. While the CTE gives me the results I expect, the final select is

A place for members of r/PollyWantACracker to chat with each other

Hi all,

Have been having ongoing issues since early December, likely a few issues. Started with pain around my right rib which turned out to be enlarged/fatty liver. This has been managed with a better diet pretty well.

Around the same time I also developed a pain on the lower right side, near my hip bone. Have had multiple ultrasounds and nothing turns up (aside from the liver).

Last several weeks I’ve had intermittent pain in my right testicle. A tender, almost throb feeling. And now a pain in the area of my bladder, which seems to get worse while going pee. Also bring woken up in the middle of the night to pee, which is totally abnormal for me.

Went to the clinic today and saw one

Hello,

I just wired up a Nest thermostat (the cheaper, non learning one) to my gas unit heater in the garage.

I was expecting to have to connect a C wire for the thermostat, which my heater does not have. So I used a piggyback spade to connect off the COM terminal on the board and wired this to the vacant W2 on the terminal strip. I get steady 27 volts between W2 and ground.

I also have W, G, and R wires connected.

Thermostat works fine if the C wire is not connected. But there is a “Note: N260” on the screen and the app says I may have power issues. Heat works. Fan works independently as well.

If I connect the C wire, it immediately goes to a no power m20 error.

Unit is a Reznor

Hello,

I just wired up a Nest thermostat (the cheaper, non learning one) to my gas unit heater in the garage.

I was expecting to have to connect a C wire for the thermostat, which my heater does not have. So I used a piggyback spade to connect off the COM terminal on the board and wired this to the vacant W2 on the terminal strip. I get steady 27 volts between W2 and ground.

I also have W, G, and R wires connected.

Thermostat works fine if the C wire is not connected. But there is a “Note: N260” on the screen and the app says I may have power issues. Heat works. Fan works independently as well.

If I connect the C wire, it immediately goes to a no power m20 error.

Unit is a Reznor

Hello,

I have a Reznor hanging unit in my garage which has just started giving me problems. Come home from a weekend away and found the unit to be making a weird noise and not heating. Garage was down to 5C and it typically sits around 10C (lowest thermostat will go).

The board had one consistent flashing green LED and the orange was off. According to the panel, this means a normal call for heat but no fire yet.

I checked the pressure switch and it was open - no voltage across it. Found the venter motor to not be running and making a lot hum. With the power and gas off, the blades spin freely. With the power on, I was able to get the venter running after about 10 tries of trying to spin

Hello,

Woke up this morning to a cold house and found the nest wouldn’t turn on. Blank screen with a flashing red LED.

After looking that up, I removed it from the base and plugged it in to a charger for 30 minutes. Plugged it back in to the base, it turned back on and was able to get the heat going again. However, during this time many menu items said low battery and the nest was not connected to wifi. Left it for a while hoping it would resolve itself, but after about 30-40 minutes it turned off again and went back to the red flashing light.

No idea why this is happening. It’s been in use for a year without any recent changes. C wire is connected and the readings on the Nest looked ok