Rediwed

Question, which ADAS features get disabled when you hook up a trailer or bike rack?

Specifically, does HDA / Lane Follow Assist still work for you?

Hey guys, are these signs of under-extrusion? I've already done a few cold pulls, and it appeared to have improved a little bit.

Just a couple prints ago, I've had to fully replace the heatblock, heatbreak, heater cartridge and nozzle. Then I had similar issues as to now. I'd rather not replace these parts again, because they cost close to €50.

Some things I noted:

• A clicking noise coming from the Bowden extruder. I have a video of this happening, and can put it on YouTube for reference.
• After unloading filament to do a cold pull, I noticed the filament was scuffed at certain intervals. Might it be the bowden extruder is not able to push the filament through the heater assembly and noz

I've been printing for a small month now and have had numerous successful and failed prints.

I am working with a Prusa Mini+, using PLA+ from a local respected brand. The nozzle temp at higher layers is 215 degrees (PLA is rated for 195 - 235 degrees), and the bed is heated at 60 degrees (PLA is rated for 55 - 75).

I tried printing my first bit print, which was going to be almost 18cm high. After the first 1cm of printing was successful, I started getting intermittent failed layers. The layers failed throughout.

I thought the plastic is not cooling down fast enough. However, randomly multiple layers will fail, and then multiple layers will succeed. As such it doesn't seem temperature woul

Hi all, about a week ago Windows suddenly enable 'Use the Print Screen key to open Snipping Tool', which had overridden Snipping tool to be triggered instead of ShareX. Took me a while to figure that out. After turning off the option, ShareX doesn't trigger anymore!

Can anyone help me get ShareX working again? Thanks!

Hi there, I was wondering if anyone has experience utilizing the totepack as a office-bag as well a camera-bag. I love the bag's design and features, but most of my use would be for Office equipment; laptop, chargers, mouse, usb-dongle, access-card, and perhaps an umbrella. I understand the totepack is perfect for camera-gear, but does what also mean it's good for office-gear? I will be using it for office stuff about 80% of the time, and 20% off the time for camera-gear.

I'm looking for a good, high quality, laptop sleeve that fits the Surface Laptop 4. Does anyone have any idea? I'd love a non-chinese brand if possible.

Thanks!

Was je tot 2021 student en heb je vorig jaar voor het eerst een volledig jaar gewerkt en verdiend? Mogelijk kan je extra belasting terug krijgen!

Middelen van inkomen is een manier om de belasting die je betaalt over je inkomen in box 1 te verlagen als je inkomen sterk wisselt over 3 aaneengesloten jaren. Bijvoorbeeld als je eerst niet werkte of enkel een bijbaan had, en nu fulltime werkt

Het idee is dat je het gemiddelde inkomen van de 3 jaren berekent en daarover de belasting opnieuw berekent. Als dit lager is dan de belasting die je al hebt betaald, kun je het verschil terugvragen aan de Belastingdienst. Er geldt wel een drempelbedrag van € 545.

*Let op, onderstaande is een versimpeld

I have this issue frequently where Google Play Services and System UI go rampant on my battery. Battery dying in 18 hours, GPS and System UI both at the top with ~9% use.

It's fixed when I wipe the cache in recovery, but when I'm on the go I don't always have a charger with me. Somehow won't boot into recovery with volume down + pwr button, it needs to be plugged in?

Why is Google Play Services battery drain STILL an issue with Android? It's been what? A problem for 5+ years? And for some reason wiping GPS storage while the phone is online doesn't work.

Any tips on getting into recovery on the go (without charger)?