SSBUplayer

u/SSBUplayer


r/ASUSROG•

My 2023 Asus Flow Z13 when plugged in or manually switched to 165hz does not switch to the NVIDIA GPU anymore causing crazy screen tearing and glitching. When manually switched in the NVIDIA settings to the NVIDIA GPU, the problem resolves itself but removes auto-switching functionality. When switched to ultimate mode the problem resolves itself with the same caveat. I have tried what seems to be every setting and every trick and nothing has worked thus far. I have tried wiping the laptop to no avail.

10

r/fordranger•

I am planning a swap for my 1994 4x4 4.0 ford ranger and in the process will be swapping from auto to manual so I don't need to deal with a TCU and have opportunity of better mpg. I need to fab a custom engine to transmission adapter and to locate the transmission correctly in relation to the flywheel I would like to know how far off of the block that the flywheel sits. I have no reference as I only have the automatic flywheel to base off of, but does anyone know if it sits flat on the block in plane with the mounting surface of the transmission and the offset is a part of the flywheel, or if there is a shim, or if the mount for the flywheel is offset from the plane of the transmission. Any

22

r/fordranger•

I recently bought a 4x4 '94 xlt ranger, swapped the transmission, and life has been great, other than the gas mileage. I am getting about 200 miles to the tank and I am driving absolute grandpa style. I replaced the fuel pump, filter, 02 sensor, cleaned maf, replaced IAC valve with a junkyard one that i soaked in carb clean along with distributor and plug wires from a junkyard, and new spark plugs, and it has no cats so they cant be clogged. It runs good and starts instantly after changing the IAC. It has 31" tires so pretty much stock and the 3.73 limited slip diff so geared low but not that low. the filler neck has some cracking, and it idles a little little rough but I dont think that cou

12

r/fordranger•

I have a 1994 Ford Ranger XLT 4x4 with a very leaky A4LD transmission and there is a 1991 Explorer 4.0 4x4 A4LD transmission for 450 cad near me with only 160k km. I am wondering will it be a direct fit? I know this question has been asked before but i can only find examples with the 4r55e or 2wd, nothing exactly like what I have. My main concern is that I heard the 4x4 is different between them so I am worried the output shaft might be different. And I also heard the shift mechanism is different, is this something to be concerned about? or is it an easy swap over from my old transmission? Thanks for entertaining my question and thanks for taking the time to read it!

61

r/Datsun•

Hey, i’m well along with my 260z restoration and it’s time to replace the floor pans. I really like the look of Resurrected Classics option s it comes with frame rails for a very decent price! Though I have my concerns. They don’t seem to conform to the curves of the trans tunnel, will this be negated after cutting? And I have not seen a single review or video featuring their floor pans.

Have any of you bought and used them? If so how was it. All insight helps!!! Thanks!!!!

40

r/RX7•

Hey, Im looking at acquiring a donor 13b for my build but I’m new to the rotary space so theres some things to learn. Im wondering how much the milage on a motor really matters if I’m just about to pull it apart and replace all seals. On a conventional piston engine I wouldn’t worry much at all, maybe put a borescope in and look for scoring, but I assume there are some different procedures to a rotary. All input around the space of purchasing a donor engine would be appreciated! Thanks!!

411

r/Detailing•

I have been watching a lot of videos and researching cutting and polishing for my 2004 acura rsx, but none seem to mention brand of pads! I have seen a couple suggestions on other threads but all seem to be like 30$ a pad and if im going through 6 cut and 6 polish pads that seems crazy!!! It seems like I could hire someone to do it for cheaper than it is to do it myself! What cheap ones are you using and where do you get them

56

r/Datsun•

Im wondering if anyone has used, or installed the Godzilla raceworks universal wiring harness for a 240 or 260z. Im buying a 260 swapped with a 240 motor with some electrical gremlins in the lights and think this could be a great solution. Any advice helps!

13

r/Acura_RSX•

Hey, im about to install a kill switch on my 04 rsx and im just double checking that the ground for the relay will be the black wire? and to install a kill switch i just graph a switch in the middle of the fuel pump relays ground correct? Sorry for rudimentary question. Thanks!

12

r/Acura_RSX•

Hey so lately ive been searching for a half decent mode of an 05-6 rsx front bumper but seem to be out of luck. If anyone has any leads on a good model of even a full car or 04 below bumper Please let me know, I just need something to work off of atp, I can measure myself. My current best idea is pulling a model from Forza but im suspicious about the accuracy of size and shape. Any help helps!! Thanks!

11


r/icbc•

One of my close friends just got into a crash and his car is like 95% going to be totalled. He has the exact transmission I’ve been looking for. Once icbc totals it out is there any way to be the first to have a crack at it? Its totalled due to quarter panel damage so should I just watch adesa auctions. Any insight helps as I really know little about car insurance and its intricacies, Thanks!

311