Source

ShearMe

u/ShearMe

r/Knife_Swap•

[WTS Post Office Blowout] WE Knives Meades Swordfin, WE Knives Guthrie, A2D Mk3 Medium Barlock, Sean O'Connell Lil Rascal, Microtech Ultratech S/E, Space Monkey Epoch

https://i.imgur.com/AZK3XXS.jpeg

I am not the first owner, but cannot find any signs of wear. Factory edge appears unused and is sharp. Perfectly smooth action and solid lockup with no blade play. Free drops with lockbar riding on blade.

Like new. I am the original owner and have never carried or used this. Perfectly smooth action and solid lockup with no blade play. Free drops with lockbar riding on blade.

  • [Attention 2 Detail Mercantile Mk3 Medium Barlock -
814
r/Knife_Swap•

[WTS but not to Clanker Moderators] Cold Steel Range Boss, MBK Slayback, Sandrin Knives Monza, WE Knives Meades Swordfin, Kansept Knives Agent, WE Knives Guthrie, A2D Mk3 Medium Barlock, Sean O'Connell Lil Rascal, Microtech Ultratech S/E, Space Monkey Epoch, Nick Chuprin Custom BBM v2

https://i.imgur.com/clvUm39.jpeg

Knife is old but I never carried it. No signs of rusting, factory edge is still sharp as ever.

Handle ano and hardware finish modded by previous owners. Factory edge could use a touchup but will still cut. Action and lockup is solid and smooth without blade play. Does not free-drop.

Has been carried, used, disassembled, and sharpened at home. Only sign o

13
r/Knife_Swap•

[WTS] Mods Suck Knife Purge - Cold Steel Range Boss, Real Steel G-Frame, MBK Slayback, Sandrin Knives Monza, WE Knives Meades Swordfin, Kansept Knives Agent, WE Knives Guthrie, A2D Mk3 Medium Barlock, Sean O'Connell Lil Rascal, Microtech UTX-70 S/E, Space Monkey Epoch, Nick Chuprin Custom BBM v2

https://i.imgur.com/clvUm39.jpeg

Knife is old but I never carried it. No signs of rusting, factory edge is still sharp as ever.

Very minor signs of wear via a few snails in the handle finish. Carried a few times but not put through any serious duty. Factory edge is still sharp. Action and lockup is solid and smooth without blade play. Does not free-drop.

Handle ano and hardware finish modded by previous owners. Factory edge could use a

13
r/Knife_Swap•

[WTS] 24hr Knife Purge

https://i.imgur.com/AJFoX2D.jpeg

Top Row

Knife is old but I never carried it. No signs of rusting, factory edge is still sharp as ever.

Very minor signs of wear via a few snails in the handle finish. Carried a few times but not put through any serious duty. Factory edge is still sharp. Action and lockup is solid and smooth without blade play. Does not free-drop.

Very minor signs of wear via snails in the handle finish. Factory edge is stil sharp. Opening/closing ac

1422
r/CommercialAV•

Logi Rally - BYOD setup

troubleshooting

Quick memo, because I couldn't find this info online anywhere. When setting up a Rally Bar for BYOD mode (no provisioning, no Sync account, etc.), you still need to connect the device to the internet for initial config. Once connected, the device checks for new firmware, and only then can you select BYOD as a "service provider" to turn your TAP into an expensive remote controller.

Logi's Sync App allows you connect directly to the device with USB for firmware updates, but will not push the initial setup wizard into the "select provider" page.

28
r/Miata•

Strange misfire with an NB

NB

I'm about at my wit's end trying to track down this issue in my '99 NB. After driving the car around for a few hours on a hot day, once the chais heats up, I start to get misfires in cylinder 1 at idle. This comes and goes on a bit of a cycle while idling, so it seems like an electronic control issue. Is starts off barely noticeable but as I keep driving it gets more severe and shaky for the car. Continues under light throttle application and acceleration, but goes away with the foot down and while cruising.The only "fix" I have found is unplugging the coolant temp sensor, which obviously puts the car into open loop rich fueling.

Engine was replaced at some point and has under 50k miles on

18