Streupfeffer

Good Day everyone.
i just bought a set of Accentum Earpods.

Has anyone found a way to make android recognise them properly as BT LE devices?

I already contacted support which confirmed that the App is the only option though. Maybe someone had any luck or found a workaround.

I'm was hoping to host an Auracast stream on a Booth and have the Audio be sent with a BTA1. To make joining the Stream easier, Print out a page with a QR-Code on it, like I've seen at an Airport now and BT SIG themself suggest putting up for venues to make it more obvious that a stream is available for PAs (i.e. at your gate).

But so far form what I've found, basically every Vendor just rolls their own *special

Good day everyone.

Im looking for a simple way to setup and broadcast a audiostream using auracast.

Ive found a couple dongles that support it but they all need manual enabling of pairing mode.

My idea:

We have a audioplay running for an event, i want a auracast stream to run along side it with explanations how the physical scenario looks like the play is about.

(QRcode for ppls to link to it without needing to open their BT settings would be handy or have a way to name it i.e."Audioplay booth 24")

Whats a good starting point/ product names to search for to do something like this?

The booth is viewable from maybe 10m around or so, im guesstimating at or below 10 ppls tops.

(No ides

Hello everyone.

We have the Exposure Mod on our server installed. It allows the player to have an ingame Camera and to take pictures with. The Pictures are saved to film rolls which have to be developed and then put on paper.
The Film rolls can be named, so the item Name would be (i.e.) "Streupfeffer_Dungeon_1"

I want to have a central development lab so players don't need to have their own. Each Team/player have their own Trainstation with a PO box to send the developed rolls back to.

Setup plan:
Each station has a drop off PO box, which then packages the film rolles and sends them to the Lab. After Development, the Lab sends the rolls and some paper back to the player for their o

Hey everyone. i had this dumb idea for a cosplay to build my own "whole body" water cooling suit.
okay not "whole body" whole body.

would mainly be comprised of multiple water pouches with a fitting on each side to allow water to pass through. A meandering path would be "welded" into the pouch to allow the water more time in proximity to skin.
NOW:

- I have looked up different foils, PE is a first pick for compatibility searching, but some fibre reinforced stuff is probably better?

- Cheap temp based welders for food preservation bags are a thing

- i have found 'through bag connectors' but haven't found low volume ones that would allow a reasonable small amount of water through.

We use this emoji quite often in the discord servers i am in, so i made it my first project. -get emoji off searchengine -print -trace with stabilo to have the boundaries -crossstitch to completion Feel free to ask questions. (Only Black is DMC, the rest is normal yarn with strands removed)

Ive promissed a friend of mine to crossstitch their logo to hang on their wall. I just did a rough marking on the canvas, its exactly 30cm wide.

As i need to buy floss anyway, should i get a 30cm (or mext bigger) frame or have the facric in my hand and "freestyle" the hold it?

Im not sure how often, if at all, ill be doing another pice that big

More technical question, im currently looking into a battery eliminator kit to have my POs run off USB power, but 80 bucks is way to much imo.

Does someone have a rough estimate how many mA a fully utilised PO takes?

Would a 300mA to 500mA LDO be sufficient to power one or even multible of them. (so a single Powersupply with a chainable dummy battery in the POs could be an option?)

Good day everyone. Recently my gfx card has started to go full speed on the rear most fan. (Towards the display connectors)

The other fans are standing still (they totate freely when nudged with a finger). This happens when gaming or just watching YT. And no matter how long i leave the PC in idle, the single fan keeps reving at full tilt, the others stay still.

The fan is told to go 100%, the rpm feedback sais the fan is not rotating. (Graph in MSI afterburner) Manually adjusting the fan speed in MSI afterburner doesnt change the running fan or the stopped ones.

I did update the driver to the newest studio one (dont need the gforceexpirence stuff) did a reflash of the bios i got from a s

I'm currently in the process of building out my VR kit for full body tracking. Looking at my controllers, i'm also planing on getting them hooked up to the power supply (USb Powerbank) of my body trackers.

Which brings me here:

• Does anyone have a pinout of the Test pads in the battery compartments so i could solder to there instead of the battery holder connections in the controller?
• If someone has attempted to solder directly onto the Battery clips, what is the Maximum safe voltage to feed in? 3V0 is expected from 2x 1.5V AA cells, but can it handle 3V3 or maybe even 5V?
• Is there a way to buy a pair (or if need be 2 pairs) of battery compartment covers?

To not have to drill

Im currently in the proces of building out my VR kit for fullbody tracking. Looking at my controllers, im also planing on getting them hooked up to the powersupply of my body trackers. Which brings me here:

• Does anyone have a pinout of the Testpads in the battery compartments so i could solder to there instead of the battery holder connections in the controller?
• If someone has atempted to solder directly onto the Battery clips, what is the Maximum safe voltage to feed in? 3V0 is expected from 2x 1.5V AA cells, but can it handle 3V3 or maybe even 5V?
• Is there a way to buy a pair (or if need be 2 pairs) of battery compartment covers?

To not have to drill up the only Battery compartment