UsePreparationH

u/UsePreparationH


r/flashlight•

SA112: 6500mAh, 3.46V nominal, 6.5A CDR, 100% efficiency at 0.2C (1.3A)

F63: 6250mAh, 3.6V nominal, 12.5A CDR, 100% efficiency at 0.2C (2.5A)

With a lower nominal voltage, you might drop out of a 3-4.2V buck/boost range a little earlier than the 3.6V battery and brightness will be slightly lower in a linear driver. The 0.2C current is also really low so you might not actually see any increased runtime outside of a low power (<5.5w) mode.

At least with the F63, you can potentially use it in a med-high current light with reduced, but not worse than 5000mAh runtimes. It just feels like a lot of tradeoffs for that SA112.

14

r/flashlight•

I am a bit new to this so I only have the Wurkkos FC11C 4000k + FC12C 6000k. I reach for that FC11C all the time, but it is just a bit too thick/big to EDC in my pocket so I'm looking for a few smaller options. I also need a UV light primarily for pet stains, but it would be nice to have a stronger one for mineral/bug hunting or epoxy/resin curing. So far the Convoy S12 UV+Filter looks good, but the 14500+Keychain lights have way too many options to really narrow it down. USB-C charging for the 14500+UV isn't required since I have an XTAR VX2 Pro, but might be nice for the keychain. My max budget is $30 for the keychain, $40 for the 14500, and $50 for the UV.

15

r/1022•

I just got a super barebones 10/22 so I was planning these upgrades. Already have both a 3-9x and red dot that I can use on it and will grab a few extra mags.

-$53 MOE X22 stock

-$43 Volquartsen Hammer

-$25 Tandemkross Bolt Keeper

-$5 Bolt buffer

I can 3D print an extended mag release or foregrip/basic handstop. Anything else I need or does it look good enough for now as a plinking gun?

610

r/Walther_PDP•

Before we start, you don't need to remind me that CA gun laws suck, I already know. I am just trying to get some stuff shipped before the Jan 1st laws take effect to save myself the headache of attempting to buy anything later.

.............

I see I have a few options.

1: 2/3 steel + 1/3 polymer base 10rnd (this is the original 10rnd mags that came with my gun)

2: Full steel dimple 10rnd (Factory made dimpled 18rnd mag w/peep holes only cut and marked to 10)

3: Full steel mag blocked 10/18rnd (This is a standard 18rnd someone has added an insert and rivet to reduce capacity to 10)

Of these choices, what do you guys think is the best and where should I be buying them from?

36

r/Walther•

I live in CA so buying anything after Jan 1 will be a bit of a pain so I want figure out what I should get now. Although I have gone shooting multiple times, this is my 1st gun so I am a bit inexperience in aftermarket stuff so any help here would be great. So far, the only things I feel I might want would be the V-spec recoil spring assembly and mag disconnect delete. Other than the mag disconnect thing being a pain to install, is the spring assembly even really worth it?

713

r/JapanTravelTips•

-I land Nov 5th at night and leave on Nov 24th in the morning.

-I plan on going to Aizuwakamatsu to see the Autumn leaves and will be renting a car for at least 2-3 days. I am still undecided on doing the 5hr Tadami scenic train + 1.5hr Shinkansen either there or back from Tokyo.

-Hakone will probably be the basic itinerary loop + Hakone Freepass 3 day/2 night trip that everyone does.

-I have a flexible itinerary for Tokyo + plenty of day trips that I can pick and choose from.

010

r/HealthInsurance•

Silver is $35 cheaper/mo and has a lower out of pocket max. The copays for most standard and emergency services relevant to me are the same except inpatient/outpatient surgery stuff which is all % based coinsurance.

https://i.imgur.com/NaOXZeP.png

https://i.imgur.com/7tbJcnI.png

If I have major stuff happen that but it is less than the Silver's out of pocket max, Gold would probably be cheaper due to low copays=slower filling OPM. If major stuff happens that maxes out the Gold OPM, then Silver would be cheaper since its OPM is $2.5k lower and I save $420/yr in premiums.

11

r/Mattress•

I am building a DIY mattress for someone with the following build M60, 5'10", 215lbs, side sleeper and they want something in the 7/10 firmness range. Here is what I am looking at as the potential setup. Total price for the mattress is ~$1200, but I can go up to $1500 max.

-Arizona Premium Queen Bamboo - Wool Zippered Mattress Cover ~$295 (to be bought later since layers may be added/removed)

-2" Sleep on Latex Med ~$200

-2" Sleep on Latex Firm ~$225

-1" HD36-HQ transition layer ~$30

-8" Quantum Edge Elite Bolsa 15 gauge ~$415

-2x 1/2" LUX-HQ base layer ~$30

-KD Frames Nomad platform (wood with 2.8" slats gap)

..................

The HD36-HQ and the LUX-HQ foams are cheap can be mov

23

r/JapanTravelTips•

It is for 2 people+luggage

We are driving through the rural Kagawa switchback mountain roads (1-1.5 lane width) and the expressway. We can either get a Kei car or a compact card like the Honda Fit.

The Kei car will make passing on the mountain roads a bit easier but will struggle more on uphill climbs and the expressway. The Honda Fit will be more comfortable and has a better engine but will be a little wider making passing opposing traffic a bit harder.

12