u/adobeamd
I was wondering if there has been any news or foreward motion on adding support for multiple "unraid" style raid pools. Im getting a lot of disks with just a dual parity and I want to start adding another. Its all just media so I dont care about performance and care much more about being power efficient and keeping the unused disks spun down
So I’m planning on retiring my old framework 13 to server duties soon and I’m trying to figure out a configuration. It will be running unraid.
From my research it has two m.2 slots, one that was used for WiFi. I won’t be needing WiFi as I will use one of the usb ports for an Ethernet adapter. Can I use m.2 to pcie adapters on both of those slots?
I have 6 atmos 6inch speakers that I bought from parts-express during Black Friday that I going to install in the ceiling. My problem is that I have blown insulation and there will most definitely get contamination in the speaker.
I was going to 3D print an enclosure for them and was wondering if it makes more sense to make a sealed one or just a tube that goes straight up through all the insulation. Installation would be much easier with the tube version.
Does anyone know how to assign workers to the fishing dock? It says I need an apprentice however I do not have any available whiskers
I’m trying to find a preferably din rail mount brake chopper. I have some 48v motors that will most likely have some regen and I don’t want to pop my psu. I’ve been looking all over the place and can’t really find any units that I can easily buy in the USA.
Does anyone have any recommendations?
I have a bunch of 18 awg wire that I’m wanting to use for my atmos and surround speakers. The longest run would be about 25 feet.
I see a lot of people recommending 16 awg for that distance but since these are not mains do you think I would see much of a difference? Or would you really recommend getting some 14 or 16 gauge wire?
X3800h will be driving some of the parts-express 6.5” in Ceiling speakers.
Does anyone have suggestions for drying PPS-CF. I got some to test out for an application and I went to just look at the drying temp and I don’t have anything that comes close to the desired 120c.
I have an amd framwork 13 7840U that I use for solidworks. I am able to model and edit 400+ part assemblies decently well using the internal GC. The problem I run in is when I try to make drawings the screen doesnt seem to update. It looks like the file loads and the measurements around the outside of the window changes when zooming in and out but the middle where I actually see the sheet and model nothing shows up.
The way for me to fix this is to open up the drawings in openGL mode and everything works as expedited. The problem now lies when I switch back to 3D editing the performance is horrible as im just using the CPU. It gets quite annoying having to switch back and forth.
Do anyone
I'm seeking some guidance to help me get started in the right direction.
Occasionally my main server crashes and this impacts a few Docker containers that handle my home automation. I’m exploring options for setting up a secondary server that can take over automatically if the main server goes down. Additionally, since the main server hosts all the data used by these Docker containers, I need a solution that can seamlessly sync any new data written to the primary server once it goes back online
At a high level how would you approach implementing such a setup?
Ive tried everything that I could think of to get my LCD screen to work with my sparkfun IOT redboard (ESP32 dev board)
I am using the TFT_eSPI library and the user setup is configured as below (everything else is commented out
#define GC9A01_DRIVER
#define TFT_WIDTH 240
#define TFT_HEIGHT 240
#define TFT_MOSI 23
#define TFT_SCLK 18
#define TFT_CS 5
#define TFT_DC 16
#define TFT_RST 4
#define LOAD_GLCD
#define LOAD_FONT2
#define LOAD_FONT4
#define LOAD_FONT6
#define LOAD_FONT7
#define LOAD_FONT8
#define LOAD_GFXFF
#define SMOOTH_FONT
#define SPI_FREQUENCY 27000000
#define SPI_READ_FREQUENCY 20000000
#define
I just updated to the newest network 8.4.62 and it seems like all of my port forwards stopped working. Nothing on my nginx proxy manager can reach the outside world anymore. Is anyone having this issue?