u/atliia
https://imgur.com/a/bVrQn80 10 ounce royal mint robin hood $380.50 10 ounce royal mint maid Marian $380.50 1 oz silver Krugerrand $38.05 10 1/10 ozt monarch precious metals $38.05 4 1/4 bullion bank $38.05 2 1/2 sunshine $38.05 12 1965-1966 40% halfs 152.12 $10.86 each 4 1964 90% halfs $12.24 each $48.97
Total lot is $1114.28 if you buy the whole thing I'll ship registered at my expense. Smaller bits shipped at your own risk and expense.
Anyone going to the protest today, and want to play after?
My grandfather is closer to 90 than 80. And he is having mobility issues. Hard to walk. Will not switch to a lighter rifle. i have been thinking about trying to print an exoskeleton to help him hold his rifle up. I would love to see him be able to make it in the woods again this year. I know he wants to. I found something on thingiverse that is similar to the hilti exo-s. Which is for working overhead.
If anyone with design experience is interested in helping an old vet that doesn't want to give up the chase stay in the woods, I think exoskeletons could be fun replacements for bipods or tripods in comps, and in the woods if we can come up with something that works for shooting. I have been
Proof with today's date https://imgur.com/a/AQjr0aZ
If you need more or better pictures let me know!
10ozt 2023 Royal Mint Maid Marian $390
10ozt 2023 Royal Mint Robin Hood $380
1ozt 2018 Silver Krugerrand $35
2x 1/2ozt Sunshine mint silver $40
4x 1/4ozt Bullion bank $40
10x 1/10ozt Monarch Precious Metals Train $40
9x 1966 and 6x 1965 40% Kennedy halfs $75.69
1x 1964 Kennedy half $12.34
1x 1945 Washington quarter $6.17
Constitutional Silver is at melt. Buyer pays shipping. If you buy the whole lot I will pay for registered mail at my expense.
hello, I am attempting to set up wireguard on a grandstream gwn7003. https://documentation.grandstream.com/knowledge-base/wireguard-guide/ I have the interface configuration setup I believe. I am attempting to configure allowed ips. And, the 0.0.0.0/0 for all ips is not being accepted. I am prompted to add a vail ipv4 address.
Also, the commented settings I am assuming they are server side, and not something I have to configure?
Thank you for any help.
I'm new here. Still on the free trial. I have not decided yet if I am going to stay or not. I do like the network much more than visible so far. I like how active the team is here on Reddit for that reason I would like to take the time to say I would love to see real hardware based 2fa. My personal preference is Yubikey.
I have looked on several podcast apps. Where can I listen to the episodes? Everything appears to be removed.
I’m hoping to begin the build this weekend. I have seen a little bit on here. Does anyone have it running yet? Comments on the process?
Adventurer 5m klipperscreen mod. I type the psk under the correct ssid on the network screen. try to click save nothing happens. Anyone have any luck connecting to wifi with klipperscreen?
I have a -3 y offset saved. Nozzle is about 3mm beyond the edge of y axis in auto home. I move axis to proper setting, and store value, then save. beeps and blue light flashes on board. Value does not change auto home goes to incorrect position. 1.1.6.2 firmware. What am I missing?
I see 25 and 26 are exclusive. The book tells you to choose either 15 or 15. Do you do both?
Picked up a Univex bc14 at auction last week. Instruction manual not very helpful. I removed the cover for cleaning. With the shaft attached. There is a lot of dried grease and gunk in the hole. I reinstalled the shaft into the grove. But, the cover is not seating to the correct depth, and will not clear the bowl. Has anyone encountered this before. There are many marks on the cover that appear to be striking so I think this probably happened to the previous owner a few times. I really don’t want to just beat it with a hammer.
