jonuggs

Cleaned out my storage unit. A fair amount of well kept 1990 series Valiant books. Am I allowed to sell here or otherwise link to sales?

Small design office has a couple of large format printers and a plotter. Looking for a solution to get our stock paper rolls up off the floor. Saw some carts from places like Safco and Uline but can't seem to find one with compartments large enough to fit the diameter of whole rolls. Probably have anywhere between 15-16 rolls I need to organize.

Does anybody have a suggestion for a good storage solution?

Thanks.

Moving from 4ga to 2ga ring for PA piercing. Should I step down the inner diameter to account for the extra size of the new ring or keep it the same?

I feel as if this is a dumb question, but please bear with me.

If I have a 5/8 hoop and want to change it out for a horseshoe style bar, should the diameter be the same? Slightly larger?

Have always been more of a set-it-and-forget-it type guy. Never really dug in much on any of this because it tends to go over my head a bit.

After discovering this subreddit and looking into things I am contemplating moving my 2040 Lifecycle into a mixture of C and S funds. Super anxious about this, though, as I had a bit of a late start to retirement savings.

I'm only 14 years in, so I feel like there's plenty of time but wanted to see what the overall pulse is for somebody like myself who has this much time in but is likely to retire in about 20 years. Also very anxious about moving funds since I am getting a late start on this.

Any insight would be appreciated.

Thanks.

Less-than-handy husband here, and getting ready to replace older sump with a battery back-up unit. The general install seems simple enough, but also want to add a check valve to the discharge pipe.

Also seems relative simple but was wondering if I need to use primer and cement on the PVC before inserting it into the check valve sleeves. Would think that the primer and cement may damage the collars but, again, not really well-versed in this type of thing. I've done the diligence and looked around for an answer elsewhere online but can't seem to find one.

Any insights would be appreciated.

Thank you.

Haven't seen much discussion on these two points, so I wanted to invite this sub's thoughts as well as touch on a few of my own.

I haven't read every single post and comment on this sub, but I haven't seen much discussion of the fossil spiral (let's call it Sedna) and how it is another connection to season 1. NOT because of the spiral motif in general, but because it resembles the Carcosa vortex from the finale of S1. Not only that, but if you look at the color palette used (and maybe squint a bit) it's not too difficult to also see the resemblance to a far off spiral galaxy.

Carcosa Vortex

Sedna

[M61 - Spi

Had a recent power outage which knocked out my sump and led to about 1"-ish of water in my basement. After clearing everything and ripping out carpet and padding I discovered channels cut into the slab. I'm assuming that these are for waterproofing.

I'm not the handiest guy, so I did some research to see if these were legit. Everything that I've seen tends to mention that any channels cut in for waterproofing are typically cemented over. Does anybody know if that's supposed to be the case, or would they just leave the channels exposed like that? Anyone have any insights?

Thank you.

Only recently got into handguns due to the wife's insistence after the insurrection. Not sure about some of the nuance, so excuse my ignorance.

My carry is a P320 compact and my wife has a Glock 43X. Neither is optics ready. How do I go about prepping them for a red dot? Is it just as easy/expensive as ordering new slides or sending off to a shop to be machined?

Thanks.

Does the MD2 conversion kit allow you to use the scenarios and tiles, as well as the heroes and monsters, from the first game? Or are the scenarios and tiles useless at that point?

Please help. Don’t know if I didn’t knead it enough, or maybe salt killed the yeast?

My weak-ass focaccia game.