ontech7

u/ontech7



r/ollama•

Hi everyone, these ten days I worked on this project called `claude-omni-rc` to run an equivalent of /remote-control of Anthropic models on Claude CLI on Telegram. I mainly use Ollama with it, but you can also use others and Anthropic models.

It uses tmux, telegram SDK and some controllers for deterministic stuff.

What I missed from Claude Code was the `/remote-control` functionality. Sometimes I need to leave and I couldn't continue my sessions. Now I just open the session via the built-in command `omni-rc <session name>`, and when I need to leave, I just open Telegram and continue from there.

You can also start headless sessions. And if you don't open via `omni-rc` (it's just a

10


r/BambuLab•

Toolhead malfunctioning [A1 mini]

Hardware Troubleshooting/Help!

Hello, this is the message of my brother-in-law but he can't post here because it's a new account, so I just copy and paste the message. I tried to help him without results :/

"Hi All,

Just got into 3d printing , jumped the gun buying an A1 mini.

Very Happy , got a few prints through both in PLA and PetG.

Turns out my luck was short lived as I encountered a toolhead malfunction error Just Yesterday After roughly 3 days of Life on the printer.

So i Guess the question Is... Any experience with this error (maybe even on the same printer?) i have contacted tech support Who advised taking down the backplate on the printer and checking the UsbC cable as well as checking this on the hotend as

10

r/3Dprinting•

Hello, this is the message of my brother-in-law but he can't post here because it's a new account, so I just copy and paste the message. I tried to help him without results :/

"Hi All,

Just got into 3d printing , jumped the gun buying an A1 mini.

Very Happy , got a few prints through both in PLA and PetG.

Turns out my luck was short lived as I encountered a toolhead malfunction error Just Yesterday After roughly 3 days of Life on the printer.

So i Guess the question Is... Any experience with this error (maybe even on the same printer?) i have contacted tech support Who advised taking down the backplate on the printer and checking the UsbC cable as well as checking this on the hotend as

11

r/espresso•

I had suspect these days that my DF54 was the problem. I always had these slow flows first seconds and fast flows afterwards. I had no problems with HiBREW G5 for a year. Why now?

So I tested again my old HiBREW G5 and check flow and taste.

With HiBREW G5 the flow was constant and the taste was good.

With DF54 the flow was inconsistent and the taste was always bitter no matter what. Even when trying to brew in few seconds (14s).

I always aim to get shots around 20-27s.

I tried to grind at similar sizes, but maybe DF54 is grinding inconsistently. I understand that conical burrs are more permissive, and flat burrs not. But failing everyday for a month seems strange.

What's your guess? Sh

115


r/espresso•

Coming from Bambino Plus after 1 year of use, new with Lelit Elizabeth since 4 days, really happy to have this monster machine.

What I’m experiencing is burnt coffee, even with reasonable brewing time. I searched all over the internet without results… I give you all the details:

I’m brewing an Blend origin medium roast for a ratio of 1:2 (18in, 36out) at 93°C setup on the machine. I’m using a DF54 grinder with stock flat burrs. The total brewing time was total of 14s with 3s of preinfusion. I know it’s too little, I was expecting a really sour shot, but instead I got a bitter burnt espresso…

I changed all the advanced settings to Dave Corbey ones.

I start brewing after 20 minutes I turne

210


r/Lelit•

Coming from Bambino Plus, new with Lelit Elizabeth since 3 days, really happy to have this monster machine.

What I'm experiencing is burnt coffee, even with reasonable brewing time. I searched all over the internet without results... I give you all the details

I'm brewing an Ethiopian washed coffee (1900-2200m altitude) medium roast for a ratio of 1:2 (17in, 34out). I'm using a DF54 grinder with stock flat burrs. The total brewing time is 24s with 7s of preinfusion (3s low pressure, 4s steam preinfusion).

I changed all the advanced settings to Dave Corbey ones.

I start brewing after 20 minutes I turned on the machine, and before start doing that I check the temperatures of the 2 boilers.

58

r/gaggiaclassic•

Recently bought from Amazon Italy the Gaggia. Fun fact: I paid 100€ more for the customs taxes, since it arrived from America instead of Italy, lol.

The problem is that this is the version for America, I didn't think enough about it. We use here nominal 240V/50Hz, in America 120V/60Hz. Even if I buy a step-down transformer I will have the 50Hz vs. 60Hz problem. The machine could not perform properly.

Is there any solution or it's better to send it back? :/

Thanks in advance

25