shiftingtech

u/shiftingtech


r/livesound•

So, now that we're a few years into it, what solutions have people found for the newer phones with no headphone jack?

  • I'm mostly looking at it from small event p.a.'s and stuff. So I need to have *some* kind of solution. I can't just tell people to "go away, and come back with a real source", as much as I'd like to.
  • I certainly do encourage people to bring their adapters. but people forget, or the need to plug in only comes up at the last minute...
  • I keep an iphone adapter, and an android (USB-C) cable around. they do more or less work...but it's flaky and unreliable, and the cables are prone to walking or getting damaged...
316

r/zfs•

so, I'm trying to replace a failed drive in a failed RAIDZ1 (on debian stable, if it matters)

​

I did the replace command, and it resilvered (twice) and then just sat there, with the status still degraded, and a "replacing-0" entry still in there. (sorry, didn't get a capture of zpool status looked like then. didn't know I was going to be making this post).

I should also note, there was 1 unrecoverable file, due to an older issue with a bad controller (I think) so initially there were a couple of checksum errors on the raidz, but not on any particular device. The impacted file wasn't important, so I deleted the file, and cleared the errors.

I then tried taking the o

31


r/RelayForReddit•

I've noticed that if my phone goes to sleep with Relay up, when it comes back, relay often seems frozen. It isn't completely frozen: switching away from it, and back fixes it, and, even odder, if you clicked on something while it was "frozen" it seems to take effect when I switch, so not really sure. Could Relay still be working, but somehow unable to update the screen?

I believe it's been happening for all the v9 releases.

Device information:

Relay Version: 9.0.9 Pro

Phone: Google Pixel XL (Pixel XL)
Android Version: 8.1.0 (27)
Device (product): marlin (marlin)
Rom: OPM1.171019.011
20

r/PrintrBot•

So I just decided to see about building a copy of stock marlin for my RevF, rather than the printrbot fork. Turns out, it's a little annoying, but not too bad. Working everything out from scratch took me about a morning's effort (most of which was just going back and finding a few config details I'd missed my first time thru)

I'm not going to list every setting, since configuration.h is pretty well documented, but I'll try to list a few of the ones that caught me off guard, or that I had to lookup.

  • Right at the top: MOTHERBOARD BOARD_PRINTRBOARD or MOTHERBOARD BOARD_PRINTERBOARD_REVF as appropriate

  • TEMP_SENSOR_BED 1 (that's correct for my non-standard sensor, I think that was rig

155

r/techtheatre•

I seem to remember that digikey or mouser used to have a connector which worked as a replacement on sennheiser lavs (1/8", with locking ring), but I can't find it now. Does anyone have the part # handy?

14

r/PrintrBot•

So after changing my extruder tip, I discovered that my z-probe was always reading as triggered. Problem is, it doesn't seem to be a probe, or wiring issue:

My probe worked fine before

the red light on my probe still turns on and off as expected

And (this is the one that really confuses me) when I completely disconnect the probe from my printrboard, it STILL reads as triggered.

Does anybody know what I've done? Or know how to fix it?

27

r/3Dprinting•

Air filters

Discussion

I know there's a lot of debate whether we need to worry about the particles coming off 3d printers in the first place, but let's set that aside for the moment. Has anyone tried building a hepa, or other particulate filter into their enclosure?

I'm thinking about building an enclosure for my Simple Metal, and I figure I might as well try to deal with the particulate thing while I'm at it. Unfortunately, where I want to setup, it isn't really convenient to vent outside. So it made me think: could I just filter the outflow air instead? But I can't find anyone else doing that, so I have to wonder: am I missing some obvious reason that it's a bad idea?

04

You've reached the end of this feed.