
void64
u/void64

We have both FM-200 and NOVEC fire systems installed in a couple of locations. Some installed recently as of 2015/2016, others older; 2006-2009.
We were recently given a deficiency estimate to install tank pressure monitors to monitor for actual tank discharge or control head removed etc. This has never been required in the past in the previous NFPA standard and these are existing installs pre change. The suppression company is basically telling is we have to do it and handed us a quote for tens of thousands of dollars.
I call BS. Since when would this be retroactive on something that has passed inspection for years and now suddenly its required on existing installs? Anyone else running i
I have one TrueNAS Core 13 server we are deprecating for a new TrueNAS Core server.
We have a few local accounts with OTP password set in downstream applications. We can recreate the accounts on the new server, but we only have the encrypted password on the old server.
We can use "vipw" to edit the password file and copy in the encrypted password from the old server? Will that persist across reboots?
I purchased several Intel D3-S4510 SSD's and they all appear to be operating ok, but after I got them installed I enabled SMART checks via smartmontools and I get two predictive fails. It's the same attribute failing on every drive, they're all the same.
I'm not sure if this is a SSD firmware thing, but the smart monitor on the drives are sending pending failure. Every one of these drives are brand new and came in OEM shrink, bought from a reputable seller.
What we're seeing:
=== START OF INFORMATION SECTION ===
Model Family: Intel S4510/S4610/S4500/S4600 Series SSDs
Device Model: INTEL SSDSC2KB480G8
Serial Number: PHYF017005BX480BGN
LU WWN Device Id: 5 5cd2
This may or may not be a 28.0.4 issue, but I onlly noticed this after trying to install an app after upgrading to 28.0.4.
Whenever I try to enable any app (even built in ones), I get "Error: This app cannot be enabled because it makes the server unstable"
If I disable something that was enabled, I can't re-enable it because of this.
Apps already enabled seem to be ok.
No error messages in the logs at all when this message appears.
Anyone else get this or know of a workaround or fix ? I can file a PR, but I just want to make sure it's not something I have wrong. Admittedly I've not enabled or disabled any new apps since going to 28. So this just might be the first time I'm no
New install. Using two 480G enterprise grade SSD's in a zfs mirrored boot pool. Upon install, chose to create the swap on the boot disks. (which is fine, we realize they're not used hardly at all, if ever)
Crated the main zpool for data. By default this caused TrueNAS to move the swap and create 2G mirrors on every device. (I get it). But I already have a mirrored zpool on the boot devices with a TON of space that's not being used.
Destroyed the pool and recreated it with the swap size set to "0". This worked as expected on the primary storage pool. No swap partitions.
However, when I did this and rebooted the server, TrueNAS will only pick up ONE of the SSD's and not the gmirror partit
I am creating a storage pool of two spinning rust RAID-Z2 vdevs; (6) 18 TIB SAS drives each. (12 drives total).
I have two Micron 7450 MAX NVMe SSDs (400G), 3DWPD endurance. I want to create these for mirrored SLOG device. While they are WAY overkill size wise; now days these drives are on the small size and Optane is hard to come by.
Reading things about over-provisioning the drive, but this seems to be for smaller devices to help with endurance? Since these drives are 400G and 3DWPD endurance, does it really make any sense at all to screw around with either partitioning or over-provisioning? As it is, this is a very low write duty on the pool; probably only upto 100 GiB written per day.
This is going to be a little bit of a rant. Coming from a TrueNAS/FreeBSD core standpoint for dozens of years. Today deploying new servers, I attempted to deploy Scale and was ready to pull my hair out when I got into the Scale network configuration. I have three different types of NIC pairs (intel 1/10G and Mellanox 25G) in a server and the naming and the way Linux presented these for use was awful. In FreeBSD it's straight forward to see the NIC driver type, interface #, etc. (and you can rename them if you want to). In Linux, NONE of it makes sense and I had to hunt down and compare mac addresses to try and find the right ports, etc.
The configuration/setup tool in Scale didn't make it
Looking at Ego to replace an aging push mower. Just under half acre lawn. Looking at the 21 or 22 aluminum self propelled. I have a Deere riding mower and use that for the majority but looking for a new push for the edge/tight spots.
Is there a way to stop the self propelled and just push under manual control? What about backing up? Read that it’s always on and cant be stopped, is this true?
On the gas Cub Cadet can just let go of the drive bar for manual control. Is this not the case with the Ego?
With latest court settlement, GCSD owes Crossgates $4.4M
altamontenterprise.com/03152024/latest-court-...W/R/T Cisco licensing on some platforms, more specifically the ASR-1000.
Feature license "FLASR1-BB-16K" is a perpetual license? Yet Cisco wants to dig you on smartnet every year for this license? This is a perpetual license is it not? You already pay a separate license on IOS + Smartnet, so what gives with Smartnet RTU on a perpetual license? What happens if you just not opt for Smartnet on the RTU. Shouldn't stop working as it's perpetual license?
I guess I'm just trying to understand these shenanigans.
Student loan forgiveness: Biden has canceled nearly $138 billion so far | CNN Politics
cnn.com/2024/02/21/politics/student-loan-forg...Does anything exist today to help provide maybe some frontend tools for users/customers at the most basic level, without needing full access to Proxmox ?
Wondering if something exists that would allow a user to log into a panel and be able to see 1 or more of VM's they control, have the ability to VNC/console, power on/off, reboot and possibly mount media?
Either wondering if Proxmox itself would have a way to limit/allow this on a per VM level (or group of VMs) or if there is some other outside administration tool(s) that would work.
So VCPP and Vmware partners not making the cut or finding the Broadcom minimums killing your business model for customer VMware hosting; have you notified your customers yet? If so, what have you told them? Has anyone got a drop dead date on the existing VCPP program and when it ends. Our best read is that it's 3/31/2024 which leaves us virtually no time to have an alternate platform to migrate workloads to. Just curious as to what other partners are doing that are not making the cut.
So our "friends" at Broadcom just dropped a bomb on all of their VCPP.
New VCSP entry level is a 3500 core commit at $350/yr (min 3 years). So if you want to be a VCPP now, you're coughing up $102k a month or $1.2M a year, minimum.
Say goodbye to 95% of the VCPP (SP/MSP) out there.... it was a good run.