What is killing my HDMI ports on my projectors/receivers?

Tech Support

Overarching problem: Content will not display to and through Epson projector via either HDMI ports.

Specifics: Projector will no longer display video from any source plugged into either of 2 HDMI ports. Receiver will no longer output video signal via HDMI. Under most circumstances, will still output audio to speakers.

Setup

Receiver: Onkyo TX-NR696 (HDMI 1 and 2 output)

Projector: New Epson LS500B (HDMI 1 and 2 input)

Source 1: AppleTV, model A1842 (HDMI out)

Source 2: Comcast Cable Box (HDMI out)

Source 3: Sonos (Audio only)

Power Management - Cyberpower 950VA

TEST EQUIPMENT

Laptop with HDMI out

Asus VW266 1080p monitor

Background: Earlier this summer, I found I was having more problems with my previous projector, a 6 year old ViewSonic LS830 connected to a Denon AVRX2600H Receiver. A year or so before, I had already switched to using the projector's HDMI2 port after its HDMI1 seemed to have failed but now a video signal was not displaying from the source, through the Denon to HDMI2. I tried directly plogging in the source and nothing worked to display an image although I could hear content through the audio system overall. Brought in the Asus monitor to see if the sources were bad and they displayed fine.

I didn't want to totally junk/toss the (long out of warranty) ViewSonic but I needed a projector for an upcoming event so I sent the ViewSonic projector to a local company that claimed they could fix anything (but it would take weeks) and picked up the Epson. Also saw a good deal on the Onkyo which among other features, had better (lagless) Sonos integration, so used that to replace the Denon. Also thinking that if somehow the Denon had damaged the ViewSonic, I didn't want to hook it up to the Epson and risk encountering a similar problem.

The new Epson/Onkyo system worked great for a couple weeks. All sources came through perfectly. Sonos part worked well. Then I started to notice slight hiccups where the projector just wouldn't pick up a signal properly. Had to reboot one or the other. Left the system for a month but a housesitter who spent part of the time there reported no problems. But when I came back, I could not get a signal through the receiver at all. The projector initially says "No Signal" but after letting it sit awhile, the message switches to "Not Supported", which is strange because I didn't make any changes to settings and I'm certain it was beyond the means and desire of the housesitter to do so.

I made do by plugging the Apple TV directly into one of the Epson's HDMI ports and that worked fine....for about another week until that stopped working, too. Now nothing I plug into either of the 2 main HDMI ports in the Epson is displayed anymore, just Not Supported.

Have reset the projector and the receiver to factory settings. Did not help resolve the projector issues and while the receiver is definitely in "first time turn on" mode according to the receiver's window display, I do not get any video output on either the projector or the Asus monitor.

Have tried swapping around cables. Using the exact same cables to see that, for example, laptop to Asus monitor works but not Onkyo to Asus or laptop to Epson, or AppleTV to Asus works but not to the projector, etc.

The ViewSonic came back from the repair place with the guy saying they couldn't fix it because they couldn't get a replacement board from ViewSonic. I talked to the guy who said that definitely HDMI2 was dead but it seemed that HDMI1, long written off, was working. So I set it up and tried plugging either Comcast and AppleTV into HDMI1 on the ViewSonic and it kinda worked. It would display video but it was unstable - bands of digital snow, big audio popping, and complete static-appearing washouts. It wasn't only uncomfortable to watch but it seemed dangerous to continue.

Got an extra "super warranty" deal with the Epson and the Onkyo is still under standard warranty and I can send them both in for fix/replace but I am concerned that there could be something else at play here that has knocked them out like the ViewSonic/Denon arrangement before and after a long warranty shuffle (assuming both are accepted), the same thing will happen all over again because I'm missing something. I know the house has had power outages during storms and such while I was out of town and I have checked the electrical power going into and out of the Cyberpower to verify that there's proper grounding but beyond that, I don't know what else to do.

Any ideas?

Posted Sep 11, 2023, 12:09 AM UTC

111
_brickhaus_•

Firmware update everything you can. Order good cables from Amazon (search '4k 120hz HDMI cable').

1
HuntredOP•

I’ll try to update but I’m a little concerned that it did work so well and then it kinda stopped working normally, and then stopped working direct. But who knows, right?

1
_brickhaus_•

Cable could be going bad.

1
blackfalcon450•

Best guess is your comcast cable box. Is the coax to the cable box going through a surge protector? My denon X4400h had the hdmi board fried because of a surge in the cable line to my cable box, that passed it through the hdmi. Protect the coax and network cables going into your system,not just the ac lines.

1
HuntredOP•

Yeah - I was on Wi-Fi for all the networking but the Comcast coax was straight in. Was hoping that any issues would be absorbed by their easily-replaceable box instead of affecting things down the line. I’ll get coverage on that for sure when I get replacements.

1
Workwilliam•

Long shot question here, but how long are your hdmi cable runs?

I had some similar issues with my Epson projector being fed by a Yamaha AVR HDMI out with Nvidia Shield Pro, Roku, and Blu-ray player as sources. Some of the same issues with no audio or video, just audio sometimes, or not compatible message.

Turns out there are such things as OPTICAL hdmi cables which work better with longer runs: mine was 25’ and apparently just a bit too long for a regular hdmi cable and flaking out on me. This may not be your issue, just taking a shot in the dark.

1
HuntredOP•

Thanks for replying - I’m maybe 10’ at longest (my fav test cable since the stack is in all disarray now). Most cables are less than half that.

1
liquidatorboris•

Get a tester and dim the lights in the room.. while every component is turned on check if there's any electricity passing through the HDMi cables by simply touching the flat part of the connector (with tester ofcourse) if you find any that's the culprit.. Double check on if any of the components with ground is connected with only 2 pin plugs (sometimes projectors tend to ground excess charges throughout their circuit and in turn the HDMI cable..

1
Dt2_0•

Cable boxes. They get an amplified signal and tend to burn out HDMI ports over time if that signal is not filtered by a surge protector.

1
thedavej•

Do you mean filtering the coax through a surge protector?

1
Dt2_0•

yup. Cable boxes get a really amplified signal. That heavily amplified signal can burn out HDMI ports. A good surge protector should also clean the signal coming in.

1