Need advice on new home wiring/network configuration

I would like to wire my two story home with cat6, my current setup is just an SB6183 and an R7000 router. I want to run at least two lines to each bedroom and the living room.

The starting point would be located in the office on the second floor where both the modem and router will be located, from there I wanted to run the Ethernet out from the router to the attic where the switcher would be located. From there simply run the lines to their respective destinations and setup the other side with the plate/keystone connector

I am not quite sure whether or not I should be using a patch panel or not, It doesn't seem necessary for my setup because I wouldn't be connecting/disconnecting lines very often. Unless it serves another purpose.

Also I realize that I am missing a punch out tool, I don't which size I would need for the job.

I would like any educated input on the matter whether it be oversights or overkill, considering I have never done anything this in depth with networking before

Switcher

RJ-45 connectors

RJ-45 crimper

Cat6 ethernet cable

Keystone Jack

Keystone wall plate

Posted Mar 10, 2015, 5:26 PM UTC

714
dcoulsonCisco•

Use a patch panel. It's more organized, and you'll be able to terminate cables much faster and more reliably on a patch panel or keystone jacks.

Here's a decent tool: http://www.amazon.com/Cable-Matters-Punch-Down-Impact-Blade/dp/B0072K1QHM

Also, just buy your own patch cables rather than making them.

5
AlphaDeltaMikeOP•

I must not grasp the usefulness of the patch panel, from my understanding you would attach the lines you run to each room's plate and the opposite side to the panel, then from the panel connect to the switcher?

Then from there just buy short cat 6/5e lines to connect them together?

5
dcoulsonCisco•

The in-wall cable will be solid and pretty much won't move. It makes more sense to terminate in a patch panel, then use more flexible stranded Cat5e/6 to connect to the switch (not switcher). This will make changes much easier. Also it just looks better.

1
phunkygeeza•

It is absolutely worth it. For the few extra dollars the patch bay gives you the neat, clean end to your loom. Get a decent cabinet too, you can get 'home' versions that are a bit more discreet if you need to.

A patch allows you to more easily divide your network into physical segments. For instance, if you wanted to run an analog phone line down one of your cat6 then you just jack in as appropriate. If you wanted a set of PoE IP cameras, again you can easily reconfigure. Yes it is nothing you can't do by just plugging into a different switch/device though.

But LFMF, don't run your cables parallel to mains.

1
AlphaDeltaMikeOP•

Would you be able to give some form of an example of these cabinets? Would be nice to keep it discreet, also should I look into a 48 port patch panel just in case for future expansion?

1
dcoulsonCisco•

I've been using keystone patch panels lately - It's much easier to punch down a keystone jack and shove it in the panel, than it is to punch down additional ports directly on the patch panel.

This is what I got last time. http://www.amazon.com/gp/product/B005E2YCNA

1
[deleted]•

[deleted]

1
techmattr•

If your attic isn't climate controlled check the temperature and humidity at hot/cold times to make sure it doesn't exceed the environmental operating temperature of the devices going in there. I generally recommend people install their equipment in a closet or basement.

3
dcoulsonCisco•

Totally missed that - good catch. Plus even if the hardware can handle it, it sucks to go into a hot, dusty attic in the summer to deal with something that died or isn't working properly.

1
techmattr•

Yeah I know I dread going into my attic whenever a need arises.... never know what I'm going to find.

1
osi_layer_one•

pull more than two drops into your living room. it won't hurt to have extra. while the proliferation of wireless is cool and all, nothing will beat a hard wired link.

I haven't upgraded in quite awhile and (at the time) my living room has a 360, ps3, tv, wii u, and an htpc all on wireless. granted I live in a "metro" area and the wireless channels were all getting crushed.

the only thing that is not wired now is the wii u which doesn't have an ethernet port. ended up having to buy an 8 port switch and a fiber patch.

1
mrcowdude20•

Those keystone stuff is extremely expensive...go to monoprice and look around there. You'll save a ton of money

1
[deleted]•

[deleted]

0