r/chemhelp•
Chemmqs

Suspicious behavior with an unsuspecting chemical? NMR question

I made something that has 3 phenylimidazole units (see CAS: 7164-98-9) by an Ullman coupling. The NMR came back pure in both CDCl3 and DMSO, I just think I had to re-run it because CDCl3 gave me some insoluble precipitates.

I figured this compound is polar but should be soluble having 3 benzene rings, 6 nitrogen atoms, etc. In DMSO I seem to have more sample simply due to the fact that the sample peaks are higher than solvent, where CDCl3 i have poor sample to solvent ratio ... that very well could be because there is solids in the flask. I looked at an NMR I took awhile ago in CDCl3 and saw a similar, poor peaks:solvent ratio.

My question

  1. Do you suspect anything weird is happening or is my sample just far more soluble in DMSO, but can be solubilzed in CDCl3?

  2. Would the C-N bond in this case ever hydrolyse under ambient conditions in the solid state?

  3. Would the lewis basic Nitrogen in this case ever protonate in air, polymerize, or anything funky like that? Would you see two sets of similar peaks in the DMSO spectrum if this were the case or would they look the same?

I could be freaking out over nothing, and my compound is pure.

Posted Jul 7, 2018, 2:13 PM UTC

46
MoJoStoOrganic•

>In DMSO I seem to have more sample simply due to the fact that the sample peaks are higher than solvent

You can't really make this kind of comparison, between solvents or even between different bottles of the same solvent. A solvent peak comes from the solvent being incompletely deuterated and depends on how many protons the solvent has, how old it is, how good the deuteration process is, etc.

Chloroform is a decent solvent, but DMSO will dissolve damn near everything. I love dmso, save for the extreme difficulty of removing it.

Without seeing your spectrum, I would suspect that you are over analyzing it.

3
ChemmqsOP•

The spectrum is beautiful, it's just my intuition would say something with a phenylimidazole should dissolve in chloroform, as I have some other similar phenylheterocycles that dissolve well in chloroform. Granted thats poor logic/reasoning and CDCl3 does produce signal corresponding to pure product (as does DMSO) ...

Likely just overanalyzing it. Only thoughts are that it could be silica from the column that is dispersed, but from experience if thats ever the case my CDCl3 solution would look cloudy/hazy, not literal chuns of solid floating at the top. Must be a solubility thing.

1
jsphere256•
  1. Your compound is probably crashing out of chloroform but it dissolves in DMSO. Take a TLC and make sure you don't have a mixture.
  2. Imidazole hydrolyze? Absolutely not. Extremely hard to do.
  3. Imidazoles are mildly basic, not basic enough to pull protons from water in the air. They don't typically decompose or polymerize just sitting around.
1
ChemmqsOP•

I columned it, the only thought I had is it could be silica gel that got through? NMR is pure enough that the proton and carbon make perfect sense, no excess imidazole or any peaks unaccounted for.

This time I'm redoing the reaction and I know how to better separate it without going through the column. Since its an Ullman coupling and imidazole is soluble in water and my product shouldnt be, if I wash the residue from the ullman coupling with a crap ton of water and redissolve the residue in a hefty amount of chloroform, I imagine that should do it ...

I meant the hydrolysis of the C-N bond to form a N-H bond or something. I know certain bonds have driving force to hydrolyze I just wasnt sure if that C-N is one of them

1
jsphere256•

As a good rule of thumb you should rely on NMR but second it with a chromatographic measure of purity like HPLC-MS or even TLC. A clean looking spectrum can still be a mixture of compounds.

Use ammonium hydroxide instead of water. It will help get rid of leftover copper.

1
ajp0206Organic Chemistry•

Could also try protonating all the nitrogens with DCl and taking the NMR in D2O. I work with a lot of tris-pyridine and other multi cyclic nitrogen containing heterocycles and I often have to resort to that.

Assuming the rest of your molecule is stable in acid.

1