Suitless-safe metal volcano tamer

Build

So after several bases where everyone was in atmosuits 99% of the time, I decided to run this base mostly suitless (and at 200 dupes but that's another post). I wound up with a lot of metal volcanos, so I made this

https://imgur.com/a/Jeoi0Eh

Even if dupes immediately pick up the metal, it should be cool enough to not cause scalding, and the heat/cooling shouldn't leak too much into the rest of the base

notes are in the album but I'll copy here:

Most of the insulation is ceramic, the other color is igneous rock, used more for thermal buffer

Tempshift plates inside are obsidian (fill all space that doesn't touch insulated tiles), outside are granite. Note there are 2 in the bottom of the pickup pit

Inside, drywall can be added around the border for more buffer

Steam is at ~100Kg pressure (volcano over pressurizes at 150Kg)

All internal metals are steel - probably overkill for stuff without an overheat temp that's not within 1 tile of the eruption tile

Shipping: use steel around the actual volcano, avoid shipping over the tile the volcano erupts at. Cutoff/vent inside is to deal with potential bugs with the last packet or empty buckets (I've not encountered these but others have mentioned)

Insulated pipes are ceramic, regular pipe granite, radiant gold

make sure you have some decent buffer of fluid in the tank, the thermal sensor is not one tile before the tuner input so it relies on getting steady temps

Posted Oct 22, 2020, 10:01 PM UTC

1213
thegroundbelowme•

Wow, that is a really compact metal volcano tamer. Nice work!

3
HTL2001OP•

I knew I forgot to put something in the title

1
captainflint1990•

It is a nice interesting build.

First note, There is a bug (can't find the post again) that dropping liquid on a one tile wide pit may cause liquid delete. (specially if there is CO2 at the bottom)

I don't think steel is an overkill, because with 2400 kg of steam in the chamber, you will reach a peak of 180 C with iron volcano.

My suggestion is to loop the rail line instead of chutting and sweeping back, to cut some power waste.

Also, I fear that the rail thermo sensor position may cause some heated iron to escape, and the liquid thermo sensor position may cause some packets of pwater to cool below freezing point.

My design is very similar, except that I use less steam mass, I added a second turbine, my rail keeps looping, the automation will only turn on turbines if batteries are not full, and there is a small pool of crude oil at the bottom for faster heat exchange.

Oh, and I almost forgot, some diamond tempshift plates will make wonders in your build.

2
HTL2001OP•

I don't think steel is an overkill, because with 2400 kg of steam in the chamber, you will reach a peak of 180 C with iron volcano.

I specifically meant for the rails themselves, I probably only need it right around the volcano spawn point itself but the entire rail is steel

Also, I fear that the rail thermo sensor position may cause some heated iron to escape,

I've generally noticed that, with the speed of a normal autosweeper it will pick up 40kg at a time (its not fast enough to react to 1 packet) so I haven't seen that happen. That said, I've accidentally had the thermo sensor misconfigured and due to the amount of thermal buffer on the output it was only a bit warm.

and the liquid thermo sensor position may cause some packets of pwater to cool below freezing point.

This is what the tank is for, with >1t of liquid the water coming out will be very even in temp so the sensor location will be okay

and there is a small pool of crude oil at the bottom for faster heat exchange

I wanted to try this but I was too worried about making sour gas by accident

1
Whaim•

Can you show us your build? I would love to see the improved positioning of each element since that isn’t specified.

1
captainflint1990•

Here is what I build back then. I used 2 turbines to reduce the amount of steam mass.

1
Whaim•

Sweet. What is the missing rail bridge you mention about?

1
captainflint1990•

On the left side, it should cross over the volcano from left to right at the exactly tile where molten metal.

It was meant to be built for last, as to prevent early triggering the volcano.

Because I forgot to build it before sealing the chamber, I had to improvise a connection to allow the metal to flow out of the chamber.

1
handickyrianto•

I did this. you will eventually run a problem where the autosweeper pick up milligram of iron, and the whole system stuck because of that one thing.

however you can avoid this by storing it to a bin submerge in coolant liquid of your choice with diagonal transfer.

2
HTL2001OP•

That's what the chute is meant to deal with, I've never had that happen personally but if it does, next eruption should get that last remnant to merge

1
HTL2001OP•

One thing to note is that there's no safety thermo sensor for the steam temp inside (no room), I once accidentally overheated the sweeper/loader due to running it in a hot area (one of the volcanos was in the oil biome)

2
Whaim•

How do they get it out of the pit?

1
HTL2001OP•

Dupes can reach down 3 tiles

2