Jyers firmware CR Touch Z Offset changes after Home All Axis after Levelling ?

I have an E3v2 purchased with CR Touch which works perfectly with Creality original firmware.

I installed Jyers BLTouch Firmware, level the bed and verify that all 4 corners are levelled, which I go around each corner one by one and also after levelled I check 5 times back to back without changing anything.

I Select Home All or Home Z and when I go back into to Manual Levelling and choose any corner the Z axis moves down but not the same height I just levelled to?

Here are my steps I do just to make sure I am not doing something wrong:

​

  1. Pre-heat PLA bed and Nozzle wait ~ 5 mins until hot, Make sure Nozzle is clean.
  2. Adjust my Z Offset using A4 paper and save then I Home All and go back to adjust Z Offset to make sure it goes back to my adjusted/saved position, I do this 3 times and it always positions all okay.
  3. Go to Manual Levelling and Level each corner 1 by 1, after happy go around 5 times just to check if each corner is fine without changing anything
  4. Go back to check the z offset and check If it’s still in the same position, all okay.
  5. Home All Axis and go Back to Manual Levelling and Select A Corner and Now it goes down to that point but a bit higher. Is it not ment to go the same height as you levelled ?

What am I doing wrong ? Is it ment to stay higher than previous point ? I am thinking of removing the CR Touch and putting the Z switch back on and use Normal Jyers ?

I’ve tried getting this working Jyers for 10 days nows

Posted Sep 17, 2021, 9:10 AM UTC · edited

39
crakinshot•

Yeah manual level doesn't work for me - it never has the offset applied so it useless. But also its not useful anyway, because your touch is quite accurate.

My process:

  • heat to 70, set z-offset to 0 and save, auto-level bed
  • check the level 3x3 matrix (with values), any corner that is > +/-0.5mm displaced, I _physically_ move that corner up/down, then do the auto-level bed again.
  • home-z, enable live z-offset first,
  • move the offset down until paper tension is just right, then save.
  • and thats it - you might have to do a first-layer test and micro-adjust the z-offset to get the line squish just right, but other than that it shouldn't need more.
2
Live_DistributionOP•

Thanks that at least I know this doesn't work, it feels it still does not apply the mesh at the time of printing after creating a mesh as my mesh looks green at every point shows it's reading higher at every point. It looks like I will just go back to the original firmware.

1
crakinshot•

thats a bit wierd - it should be 0 or red at least on one point.

1
Live_DistributionOP•

Actually let me not lie, Exactly right in the center where the Probe zeros is 0.0 red.

I might try Marlin firmware than if not give up lol I wonder if I fit my end switch back on and use that as z stop and than use my cr touch as mesh only lol

1
Big9erfan•

Green doesn't mean good. The more green it is the more above 0 the value, the black means 0 (or close to it) and more red means the more below 0. You want all the squares to be black or darker shades of green and red and then you can consider your bed parallel with the x axis.

You said you feel like it's not applying the mesh at print time, do you have your start gcode set to load the mesh?

1
Live_DistributionOP•

Hi All,

Finally I cracked it 🙌

I put the Jyers 1.3.3 firmware Non UBL version.

I used Manual Tunning in the Mesh Menu of the Jyers firmware appose to Manual Leveling which always stays up couple mm after homing.

I tuned/leveled it with the knobs and at some points used the microstep up/down.

I guess the only advantage of the CR Touch probe is to identify the Mesh Value and do minor corrections if anything changes.

The standard setup is good without CR Touch is still okay and my personal opinion is that the Probe gives more headache than advantage.

Here is my benchy I printed, not bad for 10 days worth of troubleshooting and learning :)

Benchy

2
UpstartBurrito•

What I noticed is that if you do your mesh and save it then go print something and just tune it down until you get it where you want while it’s printing and then once you like it just stop the print and go back to the z offset in prepare or whatever it is and scroll down to save. You can’t save it while your printing so if you don’t go back into the settings after you change it during a print and turn the printer off it won’t save

1
Live_DistributionOP•

I done this too, that's odd my z offset changes after changing it in tune menu. Unless you are saying that the number changes but has no affect ?

1
UpstartBurrito•

Are you scrolling all the way down and clicking save from the offset menu?

1