r/polymer80•
Ferrule

Feed troubles with PF45

I built a G20L a while back on a PF45 frame with all lone wolf parts but the frame. Long slide custom built with their slide configurator, alpha wolf long threaded barrel, 507c, the works. It's accurate, but having issues feeding issues probably 30-50% of the time with any ammo I have tried so far. It looks like the edge of the case may be hanging on the top of the chamber but not sure why.

If I bump the magazine on the base pad when it hangs up it will finish chambering the round 100% of the time...any ideas of common problems or things to look at?

I really like the feel of the p80 frames over the oem or I'd have just bought a g20 and swapped the big boi upper over to it to try. Also just want it to work since I spent months getting parts.

Notaglockfawty

Hangup

Another angle

*EDITED TO ADD:

Recoil spring channel 1

Channel 2

Channel 3

Chamber

Rails

Trigger bar tight fit I had to file the front inboard side of the right rear rail module back a few thou and radius it to allow the trigger bar to travel rearward enough to release the striker. Some hand fitting required fosho on this notaglockzilla. Kinda concerned if/when any grit ever makes its way in there.

Also forgot to mention I have been getting off center/light primer strikes sometimes on ammo that runs flawless in my 1911 10mm. Assuming this means it isn't fully locking up sometimes. With what I've read, the lone wolf kit comes with a 17lb recoil spring, and I'm wondering if going to a 20 or 22lb and cleaning out the recoil spring channel a touch wouldn't hurt. If I bump up to a 3 or 5lb stiffer RS, do I need to go up or down on striker spring as well? The trigger is pretty good how it is for a striker guy and I hate to mess with it, but I hate unreliable guns even more.

I'm gonna get robocop running good one way or the other, I just hope it doesn't involve trying to buy an oem glock frame...I'd rather a serialized p80 frame 🤣

Posted Jan 6, 2022, 3:42 PM UTC · edited

824
WSC213•

Are you using OEM mags?

3
FerruleOP•

Yup, oem 15rd. I was only able to find an ETS mag first and blamed the issue on that, but I've bought 4 oem mags since and same issue with all.

1
WSC213•

In that case all I can think of is polishing the feed ramp.

2
cicadahead•

I have had great performance from my LoneWolf 10mm barrel - HOWEVER - only after doing a little polish job on the feed rams with a dremal and one of those "eraser" type bits. Just gave it a good shine. Also, check your channel, I had a build with feed issues, had gotten a bit careless with the channel. Once I clean a bit more off the sides she cycled perfectly.

Hope that helps.

3
FerruleOP•

I have some felt wheels and mothers mag polish, I may give them a go and see if I can slick up the feed ramp and chamber any. My barrel is nitrided though, so I don't really want to break through the coating if I can help it.

2
Hellyunprime•

Your guide rod spring could be to strong, might switch the a less poundage spring.

2
FerruleOP•

Hmm...do you have an OEM g20 or a good running 10mm p80? Roughly how far do your cases eject? The lone wolf build drops them all at my feet for the most part. NOTHING like my Rock Ultra 1911 that slings 10mm brass into orbit 🤣

1
[deleted]•

[deleted]

2
DirtyDee78•

Pf45 builds are notorious for having this issue. It took shooting around 2 boxes of ammo with each of mine to get it running right. It’s a bitch. Do you have an oem extractor and plunger assembly in it?

Fwiw I added xp mag springs and #5 followers to my mags and it helped somewhat

1
FerruleOP•

It's 100% from lone wolf other than the frame, I've thought about trying to find an OEM G20 upper parts kit to try in it, but wasn't sure if something in it could cause the problem, or if it was my magazine locking in too low somehow since any time it hangs up, I can bump upward on the base pad and it chamber the rest of the way and lock.

I guess trying an OEM G20 upper, and then the oem slide with my lone wolf barrel would probably help narrow it down a good bit.

I've probably ran 200rds or so through it at this point, mostly factory 180gr blazer and handloaded 180xtp at 1350 and 180 HST at 1200.

2
Rebelghost88•

I’d deff try sourcing OEM parts to start replacing the lone wolf ones with. Doing that and polishing the feed ramp. Changing the spring in the mags plus follower to a #5. You’d be amazed the difference on performance from just swapping to OEM internals. I’ve also heard people having success with rockey brass. But OEM is king.

1
2018-SGS•

Check and see if an empty OEM mag has any up and down play, it's going to have a little side to side wiggle but no up and down. I agree with earlier poster about an out of spec follower could pose a problem. Also check your mag release.

1
FerruleOP•

It has 1/8-3/16" of side to side and forward and back play by eye, but only a few thousandths of up and down slack, it's MUCH tighter vertically than horizontally.

2
2018-SGS•

It seems like enough lockup on mag. My PF45 10mm had one mag that the last round will not go all the way in the chamber, but just the last round in one OEM mag out of four. I did polish barrel feed ramp and polished the chamber it does help. Even after all the polishing the last round still will not chamber on on the one mag, when I can going to swap follower. BTW, that one mag is the only malfunction I have had with feeding. The PF45 frame is a handful.

1
FerruleOP•

I considered blending the tiny wall at the top of the chamber where it seems to be hanging and I could see some brass smear, but since my barrel is nitrided I don't really want to break through the coating. I had some luck polishing up a nitrided chamber on an ar10, may not hurt to do the same to this one. Thanks for the feedback.

1
2018-SGS•

Alpha Wolf barrel, the coating in the chamber and on the ramp were scraping my cases, polishing fixed that. You may not want to do this but I {very} slightly rounded the top of the ramp did not take away any case support. She running better than I ever thought she would when I started.

2
shiers69•

I've got a similar build. What guide rod are you using? The first I tried was uncaptured and would interfere with the hole in the slide when taking it back. The second was a longer uncaptured rod and I couldn't even angle it in to install it. I've got a captured one from Lone Wolf coming tomorrow that hopefully solves my problems.

1
FerruleOP•

I'm currently using the alpha wolf stainless guide rod/flat spring. Think I'm about to order a wolff guide rod and spring calibration kit and try a 20 or 22lb. The more I shot this evening the better it seemed to run.

2