Lexons

u/Lexons


r/ASUS•

Hi, I have recently updated my ancient bios on my Asus Rog B450-I Gaming motherboard to version 5003 and I was able to boot just fine after the update. However, I cannot seem to make any changes to the bios and have it boot again, any change that needs a "save and reset" will brick the motherboard with the DRAM Led permanently on (no way to get into bios).

System information:

  • Mobo: Asus ROG B450-I Gaming
  • CPU: Amd Ryzen 1700x (no overclocking)
  • GPU: Asus GTX 1070 (no overclocking)
  • RAM: 2x8GB HyperX Fury 2666MHz (no overclocking)

​

Steps I've tried so far:

  1. Updated the bios to version 5003, was able to boot without any changes.
  2. Rebooted to bios and changed fan curves
13

r/Fedora•

For those who still have not seen the Fedora 38 update show up in Gnome Software, try manually removing the DNF cache directory under /var/cache/dnf.

Once you have done this, check for updates again in Gnome Software, the Fedora 38 update should now show up :)

Note; This was most likely caused by setting keepcache=True in /etc/dnf/dnf.conf.

21



r/kde•

I am trying to 'overwrite' the default icons that a look-and-feel theme (that I downloaded on KDE) uses. That would make using Yin-Yang or Koi a lot easier.

I found this tutorial on how to create a custom look-and-feel theme, so I created my own one based of the look-and-feel package that I wanted to change. And this custom theme does show up in the KDE settings, but not when I run lookandfeeltool -l (which is what Yin-Yang and Koi use to check for available themes)

I

32

r/ender3•

So I enabled and fine-tuned Linear Advance, disabled all the coasting, combing and wipe at end settings in the slicer.

I read online that you should recalibrate the retraction settings because Linear Advance will handle most of the pressure buildup in the nozzle, which will also help against stringing.

I used to have 6mm at 45mm/s retractions but I am wondering what you guys are using with linear advance? I am curious in what range I should be calibrating (I know, not all printers are the same, and yes I will still calibrate mine with the two towers).

My current setup:

  • Stock hotend with metal extruder and Capricorn Bowden.
  • K value of 0.7 for PLA.
22

r/th3d•

Hello everyone, I am thinking of upgrading my CR20 Pro board with the SKR mini e3 to get 32bit processor and silent stepper drivers.

The board in the CR20 is almost the same as found in the Creality Ender 3 (so the SKR mini e3 is an exact drop-in replacement), except the CR20 uses dual LCD display cables (EXP1 and EXP2).

I noticed that the SKR mini e3 only has the EXP1 header, I am wondering if the adapter board from TH3D would work on the SKR mini e3?

PS. People using the CR10s would face the same issue (besides the dual Z stepper issue)

**TL;DR: Does [this adapter](https://www.th3dstudio.com/product/ezboard-

10

r/BIGTREETECH•

Hello everyone, I am thinking of upgrading my CR20 Pro board with the SKR mini e3 to get 32bit processor and silent stepper drivers for less than the TH3D Ezboard.

The board in the CR20 is almost the same as found in the Creality Ender 3 (so the SKR mini e3 is an exact drop-in replacement), except the CR20 uses dual LCD display cables (EXP1 and EXP2).

I noticed that the SKR mini e3 only has the EXP1 header, I am wondering if the adapter board from TH3D would work on the SKR mini e3?

PS. People using the CR10s would face the same issue (besides the dual Z stepper issue)

**TL;DR: Does [this adapter](https://www

24