Just what it says in the title. Pulled out of my current machine.
$75 shipped to CONUS. $70 local to LA County/Santa Clarita area
(Image)[https://imgur.com/a/Gem4T3J]
u/Mguyen
Just what it says in the title. Pulled out of my current machine.
$75 shipped to CONUS. $70 local to LA County/Santa Clarita area
(Image)[https://imgur.com/a/Gem4T3J]
45x30s 6400 ISO. Stacked tiffs in DSS then stretching in Lightroom
4 minute 400 ISO jpeg from the camera stretched in Lightroom
Previous jpeg before any edits, only cropped.
[2 minute 400 ISO raw sub stretched in Lightroom](https://preview.redd.it/52y8weik2vic1.jpg?width=2254&format=pjpg&auto=webp&s=9588754de2226fbca6cd881
Magnetospeed sporter chrono - $150 Shipped SOLD
-Used once to check subsonic loads then realized I don't have another use for it. No wear except some tape residue on the rubber mounting pad. Comes with everything and the box.
Romeo 5+high and low mount- $85 Shipped SOLD
-I've lost the lens caps on this along with the original box. There's a corner that has had the finish worn away slightly as seen in the photos. Glass is in perfect condition.
EDIT: Timestamp just in case
~~This build was used for emulation and VR gaming. Never been overclocked since I just got the 7350k for the single thread performance and it's been sitting in that B250m socket for its entire life. No defects or issues. Intel stock cooler included. Not looking to part out. Will come inside of the original motherboard box in the anti static wrap.
$125 Local to DFW $140 shipped to CONUS
EDIT: The motherboard will not come with the IO shield as I can not find it
EDIT2: Pending Sale~~
SOLD TO:u/tbrown78
I'm currently trying to design a small, lightweight, and relatively low power (8-25W) repeater to integrate into an RC aircraft to get local coverage in hilly and possibly forested areas.
I've got a fair idea of how I'm going to set up the electronics and control side but what it boils down to is the rx and tx antennas are going to be in very close proximity and from what I understand so far it'll cause quite a bit of desense on the rx side if I just use the bare radios. I hear that setting it up as a crossband repeater might help but I'd like to keep it to 70cm if possible. Cavity filters seem a bit too heavy and large in addition to being rather expensive.
My question is that I was
As the title says, I wanted your opinions on which type of solder is best. Quite recently I've had a run in with a couple of batches of Lead-free solder and got less than stellar results. Wondering if I should stick to lead based or use either or.
So I just got home and looked over the octo again. All but one motor are salvageable and one out of two of the batteries are dead. The other of the two was maintained by the person who returned it, perfectly balanced, at 11.0 V. The HKpilot, GPS, Fatshark Pilotcam V2, 200mw VTx, and 100mw Telemetry Tx.
I can't believe I used to use this controller combo with this setup. I'm so taken aback at my old self. It's like an old time capsule :D
From what I was told, a guy came knocking a while ago with the wreckage in hand. Upon being asked, he let out that he analyze
After being missing for 3/4 of a year, it appears my octocopter turned back up.It seems that the RTL system kicked in and the redundancy on octos is entirely underrated xd
All jokes aside, I'm really grateful to whoever may have done this. It wasn't an easy task as I didn't expect to lose it, and as a result, didn't have contact info on it. Now I've got a long 2 week wait until I can start rebuilding it into my new AP platform. :3
EDIT: FORMATTING FAILURE