PrairieWiFi

I have the 4ft Holiday Coro singing pumpkin. Does anyone have this modeled and would be willing to share the model? Specific details 17RGB v3. I'm pulling my hair out. No matter how much I fine tune it just looks horrible.

I have ePON service and a x5001 gateway. I just noticed that this connection was offline and my router kicked over to cellular backup. Upon looking into this I see that the PON light is off on the x5001. I power cycled and stood there and watched. PON light never even blinks.

The last time a tech was out they left a x5001 laying next to the one thats currently active. For the heck of it I plugged that one in and PON lights up after about 10 mins of booting up. So I talked to support and asked if they could just activate the other CPE and they said no and would require a truck roll. I hate to waste a field tech's time coming out just to swap the modem. Anyone know of a way to just activate

Sent a modmail message about checking service availability of gig pro at an address.

Currently have 6inch insulated flexible duct running from a fresh air vent directly to my RA. I want to add a filter box and Damper online to a) filter and b) have some control over that fresh air. What my concern is this flex duct is running through conditioned space (basement) and want to avoid condensation.

Anyone recommend specific items?

Thanks in advance

For the past 5-7 days I have seen intermittent packet loss on my GPON service. I have a fiber power meter but every time I go to check things seem normal and would appear there is a different issue or the issue has cleared up.

When I call support they run through typical HFC troubleshooting even when I explain that this is a fiber GPON connection. To avoid possibly a unnecessary truck roll I am curious if historical signal levels are kept even for a short period and could someone take a look?

Does anyone know how to get Plex contentID to use with Roku ECP. I want to launch Plex and immediately play specific content. I have tried the ID that you get from the Plex API but doesn't seem to work.

I have a Photo Eye "tripwire" style sensor that has dry contacts. It has a Normally Open, Common, and Normally closed wire. On the Qubino I have no idea which terminal to connect NC and Common from the Photo Eye so that the Qubino gets the input from the Photo Eye.

All of the documentation for the Qubino talks about output to a Garage Door to open/close or similar. Not the Qubino getting the signal and relaying that to my hub.

Any help would be greatly appreciated.

I usually have issues with the first few people that answer the phone in the call center. I guess it's probably partly because I have EPON (not RFoG) and I was under the impression there are not alot of deployment like this.

The last couple days I've noticed performance issues here and there. I fired up ping plotter to see if I could see where the issue was happening. I could see high packet loss at both the inside of my CPE as well as the first hop into Comcast's network. I tried power cycling the CPE and replaced the patch cable going to the CPE. None of my trouble shooting steps changed anything. When I called the support line they said everything looked good and was a client device iss

Anyone know how 5G is being deployed in Rural areas if at all? It was my understanding that you have to be pretty close to a node and possibly much clearer line of sight.

Does it seem normal while trickle charging a completely dead 12v battery on 2020 SE Hybrid that the front and rear indicator lights flash rapidly and I hear clicking in sync with lights?

Does it seem normal while trickle charging a completely dead 12v battery on 2020 SE Hybrid that the front and rear indicator lights flash rapidly and I hear clicking in sync with lights?

A little less than two weeks ago my EPON connection died. Modem had power light on, 2.4, 5, and MOCA as well but PON off. Powercycled and nothing. Took forever to get ahold of someone. They said all they did was send a refresh signal. Things worked until tonight and same issue all over and same resolution. I just need this to be stable.

I factory reset the x5001 and could not log into web GUI with admin and password on bottom of x5001 or admin and password, admin and admin. Xfinity has done everything go hide their phone number on their website. If anyone can help that would be great.

There are random sites and apps that just will not load on my new install at my house we just built. The very same websites work fine if is use a VPN service, or disable wifi on phone or on my comast connection at the rental I was at before moving into new house. Unfortunately the people who answer the phone when you call support they only know how to have you reboot your modem or blame someone else. Please help