u/letsplaywar
I am:
Proof:
hKRib2R5hqhkZXRhY2hlZMOpaGFzaF90eXBlCqNrZXnEIwEg3RJAyjOFEh9DulO6lqHS6jC8903QSEoRcW2nN0jyKtAKp3BheWxvYWTESpcCB8QgtZ+m/CE+7AbxP1XGKGiDDjO2k5G42X1p0jzjvDjXdffEIPxcUzWe32FdU5X7e9Zm1WryhTROOK9Za/3IZSZ1Ehn3AgHCo3NpZ8RA1R2+AEkP8mQUkjJdyZ6NTmxA8brkgHWsWwd+x8GzIwHJr0bthIkylVfW4J8xiiHMH7Av+fcsXKZ+15956VOiD6hzaWdfdHlwZSCkaGFzaIKkdHlwZQildmFsdWXEILNHGMvDltwc2WZpX28NzAWMYeUqTGwZ3NhsjBEyrYgZo3RhZ80CAqd2ZXJzaW9uAQ==
Was curious if anyone on here has a Blue Book and wouldn’t mind seeing if this cue is in there and what it is valued at? Thanks!
https://i.redd.it/4qhmlg79boa21.jpg
https://i.redd.it/glkg4bp9boa21.jpg
https://i.redd.it/d14x9o5aboa21.jpg
Don't see too many Bill Yao watches on here so figured I would share this Seafighter I recently acquired. I purchased it from the original owner who purchased it directly from MKII back in 2009 when these were first produced. Designed with a heavy nod towards the Blancpain Bund 3H, a watch built for the German Military and elements of the Omega PloProf. The heart of this watch is an elabore grade 2863-2 ETA movement. Weighs about 99 grams without the rubber strap so definitely wears heavy on the wrist. I will be sending this into MKII for a
I am running an Lc2i to convert my subwoofer outputs on a 2015 Ram 1500 with the Alpine 9 speaker system. The Lc2i is pushing a signal to a JL Audio JX1000D. All gain and bass boost is zeroed out on the amp. I am running (1) Kicker Solobaric Q Class 12" specs Woofer [in, cm] 12" 2Ω L7 Continuous Power Handling [Watts RMS] 900 Rated Impedance [Ω] 2 Frequency Response [Hz] 20-100
I am not pushing the speaker very hard and keep having issues with the voice coils warming up. I can smell them if I run the speaker hard enough, and I'm not pushing it very hard at all. Any ideas? I'm guessing clipping, but not sure why or how it's clipping. Never had a subs voice coils do this to me, but I usually
Visiting beautiful Warszawa for a few days. Any pointers for must see places, night life, etc? I am staying in Old town at Patchwork. Dzięki!!
Recently on a trip back home my softail started to miss a little bit. I made it home safely and did some diagnosing. My vacuum petcock has been acting up so I replaced it and capped the vac line. Thought I was golden on a test ride until the bike died right at the bottom of my driveway. Get it in the garage and notice I'm running on one hole. Put my hand over the exhaust and feel no air moving from the front jug. Pull the exhaust, sure enough exhaust valve isn't opening. I pulled the pushrod covers and the front jug pushrods are not moving at all but I can still rotate them in my fingers by spinning them. The only thing that I am concerned about is the intake valve pushrod isn't moving up or
