physpher

Ender 3: I have a glass bed now and I feel like it's overkill to take it off and wash it with soap and water after every print. I do a good amount of printing while I'm away (my wife is home, but not interested in the slightest outside of taking pieces off for me). I feel bad for myself if I start a print right after, but I also haven't had too many issues with adhesion.

My troubles seem to happen when I take the glass off and clean it? When I place it back in place and redo my height map, the variance is too much for my liking and takes several minutes to adjust (which is fine), I just have to do this often.

I'm thinking if I can pull the parts off without my greasy fingers touching th

It was an absolute pain the past two nights. Compiling, downloading, playing with the printer, and everything in between.

Finally stumbled on https://3dprintscape.com/skr-mini-e3-v3-firmware-guide/ and got a build to work! One line was missing and one was misworded (comment vs uncomment) but was an easy fix.

• Git clone (or download) the Marlin Firmware and the config example repos separately. Make sure you're getting the same branch on both. (https://github.com/MarlinFirmware/Marlin.git and https://github.com/MarlinFirmware/Configurations.git)
• Copy Configurations/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 3.0/* to Marlin/Marlin/
• Make the below changes
• Compile (like

Is your power out too? Haven't been out and about so I don't know what kind of issue is at hand here. It's been an hour and some change for me.

Long story short, I've run OpenSprinkler for years now via a Raspberry Pi. It finally decided it didn't need a wireless interface (runs fine otherwise). I've been playing with Arduino stuff for my home assistant needs and was delighted to see there was a port of OpenSprinkler for Arduino! Awesome! Simple, lightweight and cheap.... Let's do this!

Now for the issue. I can reach my OpenSprinkler when I flash my D1 mini. However, I am unable to actuate my solenoids! For this setup, I have the D1 mini > PCF8574 (purchased due to the code in the repo) > 8 channel relay board. The only change I'm making is removing the pi and inserting the D1 and gpio expander.

I have made sure via a SPI

Hello!

I have 2 new Honeywell T6 Pro Wifi thermostats, and I am able to control them (mostly) from HA. One part that is giving me a heck of a darn time is setting the high and low setpoints for heat/cool modes. If I set those parameters from automations, it errors out. If I set them from the states panel, no error appears, but the values do not change.

Ideally, I'd like it to match what my generic home assistant thermostat does, where I can set target as well as high/low setpoints.

Any ideas on how to accomplish that? Or is this a "feature" of this specific thermostat model? Thanks in advance!

Edit: If you use the Honeywell Lyric integration, you can control all aspects of the ther

Hello!

SOLVED: bad news, I don't know exactly which change made it work, and I'm not going to change anything now 😝. Two things have happened since I've checked the status, I updated the HA OS and I added an attribute of humidity to the config. I didn't have to do that with another humidity sensor, but it is also way older and from another company. I'm leaning towards the update since my history went from unknown to off about an hour after I updated (right before going to sleep). I didn't check until I made the change to update the attribute to humidity, but I don't think it would have retroactively changed the history.

---Resolved. Below was my issue, above was a slightly vague re

Hi!

I have a command I use frequently and would like to script it out:

New-MailboxExportRequest -Mailbox "User" -ContentFilter {Subject -like "*Distorted*"} -FilePath "\\filepath\c$\temp\User.pst"

When I run the above, I get a PST where i can see the email I am looking for. When I add the same command, with variables, to my script I get my PST with folders, but no emails.

[string]$mailbox = Read-Host 'Search Mailbox User'
[string]$subject = Read-Host 'Email Subject'
New-MailboxExportRequest -Mailbox "$mailbox" -ContentFilter {Subject -like "$subject"} -FilePath "\\filepath\c$\temp\$mailbox-$subject.pst"

I have tried single/double quotes, nixing quotes for $mailbox

Over the last year, I (24m) have been working on getting my credit straightened out. In that time I have moved from a ~592 to ~720 (based on CreditKarma). I also have had kidney stones almost yearly from 2005 to today and that has led me to several ERs and doctor visits which are costly. I was stupid when I was younger and neglected to pay or set up payment plans to get these resolved. As of today, most of those have fallen off my credit report (verified a few days ago). There are still 2 that are on separate credit reports and should be falling off in the next year to year and a half, so I am just waiting on those.

Now for the fun part. I get on Credit Karma to see if there were any chan