shadowclaw2000

Setup a self hosted server just so I could play solo in my own "sandbox" and shut it down without issues whenever life got busy without worrying about bases, etc. (Minimal changes no storms, increased mining yield). Started as 10Gb memory w/ swap and then changed to 20gb.

The issue I'm having is that multiple quests/contracts seem to be bugging out. Eg. Trooper L2 w/ Kara, Planetologist L3, Journey to start specialization/Landsraad w/ Hawat.

(sword/mentat/bene all completed fine)

They won't progress / give me option to progress eg. Kara I only get the dialog option of "I can't right now", Hawat I only get "Goodbye". (I have 300hrs on live so I've done all this before)

Where relevan

Hey all,

We have had this pleco for many years and has lived long past every other fish we had with him. Sadly last week his tank sprung a leak and in the middle of the night we needed to move him into the only thing available a clear storage bin.
We are preparing to move and no longer able to properly care for him and would like to find him a good home.

Great at eating algae and keeping the tank clean. He is about 12" long so would need a good sized tank.

https://imgur.com/1XHDg3H

I'm in the final stages of replacing my Tronxy X5SA Pro board with the SKR1.4T, I think I'm pretty much done but have run into a strange issue.

When everything boots up the E0 and Bed temperature shows on the screen but after a second the bed goes to 0/0. If I click into the heating menu and go to bed the temp shows up again eg. 26/0, and may disappear again back to 0/0. The whole time E0 is fine and unchanging.

If I try to heat the bed after a few seconds it shows "Error: Heating failed, system stopped! Heater_ID: 0". I've got a bag of new thermistors so I plugged in a new one and see the same issue.

Using marlin 2.0.x bugfix and I have the bed & e0 configured as #1 100k thermist

Hey all looking for any advice on how to fix this issue.

Running a Monoprice i3 v2 with MicroSwiss hotend.

Below is a picture of the under extrusion problem I'm facing...

https://imgur.com/a/tCFEK6r

Recently had a bunch of issues with my printer that forced me to replace my thermistor, hotend heater, and I also switched to PEI vs builttak. Now that everything is running again my old settings aren't really working for PLA.

​

It seems very strange that the skirt and first part of the prints seem to print perfect but then the it seems to trail off. Printer comes up to temperature no problem, I've tried back on painters tape/glue like I used to

Nice QOL change here in the latest patch...

​

HERO UPDATES

Doomfist

• Seismic Slam
  • Can now target through railings

Mei

• Ice Wall
  • Easier to place on thin surfaces
  • Appears less jittery when placing while moving around

Reaper

• Shadow Step
  • Easier to place on thin surfaces
  • Appears less jittery when placing while moving around

Symmetra

• Teleporter
  • Players that use your Teleporter now continue to look in their current viewing direction
  • Easier to place on thin surfaces
  • Appears less jittery when placing while moving around

BUG FIXES

Heroes

General

• Fixed a bug where your view would become level with the horiz

I have the all access pass and had two windows open (their multi view was having horrible framerates) watching from start to finish the OWL matches yesterday but only got 3 Tokens. Should have been 3 per hour so it seems like I should have received 15-18.

Anyone else have the same issues?

I placed 16 in the last hot wheels round and with 13k+ cash on hand I went ahead upgrading my spoils of war... started with the wheels didn't really pay attention since normally upgrading is like 200-500 but they must have been 2000 cash each since I burned about 12k. Now I'll need like 9000 to upgrade the the Twin Mill... sigh...

On the note of all the accessibility changes one thing that has been rather annoying for some time is that when Doomfist charges his punch he loses his aim cursor and it's replaced by a white dot and some vertical bars. I find in thick of the action my eyes move to the charging bars instead. Would love to for this to be fixed.

Example.

Doomfist Punch

Checking all the other characters this animation is mostly used to choose a destination/build. Mei wall, Sym Teleport, Reaper Teleport

Examples

Mei

Reaper

Sym

The only other similar one I could