unfoundbug

After beating wave 32, we ended up in a state where the wave never started. all players had the same reach objective, but the game never actually started wave 33. It was a very dissapointing end to a nearly 5 hour run.
We tried running around the entire map killiing any stuck / respawning mobs with no luck, and the objective pointer did move always trying to get us to the same point. Up until this point the game was running slower and slower, not framerate wise, but zombies moved slower, actions like using a medkit started to take longer than the use bar. Has anyone else seen this and found a way out of it? We ended up having to force-end the game through the use of grenades in order to g

A thought I had with abortion access in the US looking at being restricted so much, does that mean that death in childbirth instead becomes at least manslaughter, or just straight up murder in some cases? Without the option to abort, Impregnation is essentially rolling a dice on if you are killing your the mother, so why shouldn't it be charged as thus.

Even in commited relationships, if the father knows the mother has medical issues which can complicate a pregnancy, then knowingly impregnating is pretty much textbook attempted murder, he is choosing to perform an action which can lead to the death of the mother. In the case of ectopics etc, its just straight up manslaughter. If the 'child'

After reading this sub-reddit, some may lose hope in the index so I thought I would put my recent experience up there for anyone considering the index.

I have had a HTC Vive for quite a few years now and been really enjoying it, so on the 25th of march, I got some extra money in and finally bit the bullet and ordered an index. by the 31st, it had arrived at my door (UK, so it came over from the netherlands). To get it started I had to uninstall and re-installing Steam VR, otherwise Steam seemed desperate to have BOTH the Vive and the Index running simultaniously. Updating the firmware on everything (yup, brand new and EVERYTHING needed an update immediately) took longer than expected, most

While discussing the possibility of a tracer night i thought of the idea (no idea if its novel, my google-fu shows no results of it being done else where) of lighting the actual field in uv (~400nm the same that is used in night clubs so safe for the eyes, the 12v strips are relatively cheap now) so that even rentals can join in, just need to load the mags with tracers. Initial results are OK, but theyre on the scale of what I can test at home, has anyone seen / tried anything like this elsewhere?

I don't normally post on reddit, i'm a serial lurker by force of habbit. Just wanted to say thanks to everyone here, I read the posts on the subreddit almost daily, and they convinced me to finally try for the vasectomy after years of "you're too young". From asking the doctor to procedure was 5 weeks, with nary a bingo in sight, just an "are you sure" from my GP and the doctor on the day. Thank the gods for the NHS. It's a massive load off now I have the sample results to say kids are never in my future and my future mental health thanks each and every one of you. So for anyone else like me lurking, my advice is this, just go, dont ask, tell. "I want to have a vasectomy, can you give me a r

I have the need for a solenoid to become active for a period of time, when a magnet is found, currently my plan is to use an SR latch and RC network https://imgur.com/a/VkCM0XJ will this actually work?

I'm looking at using the CD4043B, with VCC from a 3S lipo pack.

I am currently trying to measure what I expect to be a VERY large current draw (two large motors drawing power from a LiPo) and don't want to risk blowing out my ammeters, would there be an issue with connecting multiple ammeters in parallel in series with the load?

Ie Vin - (Ammeter in parallel with another ammeter) - (HBridges in parallel) - Gnd

As above, I have had no issues with windows 7, I updated to make sure I had a key, try it out for a bit, then revert. Considering http://imgur.com/8lP8dds this is what my primary monitor does for no apparent reason when it never did it at all on windows 7 is rather dissapointing. Is there a 'screw over the nice expensive monitor' setting i'm missing?

I have a Corsair K95 keyboard, and up until recently it has been amazing.

Last night, an upgrade was had, which necessitated a reinstall of windows (Home premium why do you have ram caps?). Since the reinstall, the keyboard hasnt worked properly since, If I run it in BIOS mode via the switch on the back, is usable as a keyboard however neither this or any of the other settings on the back allow the CUE to actually connect to the keyboard. And on any setting other than BIOS, none of the keys on the keyboard work at all.

I say recently was amazing as well, since the latest firmware patch, the keyboard either takes AGES to initialize and become usable, or requires me to press the space ba

I am looking into power supplies (Wall warts) for a new 5 volt regulator module I bought off amazon (Takes in 9v-40v, spits out 5v across 4 usb sockets). My question is this, how does the current draw from the high side (input) to the low side relate? Ie, if im drawing 1.2a at 5v (6w), am I only drawing 0.5a with a 12v input (6w)?

This is assuming a switch mode power supply, and for the purposes of calculations, no losses in conversion

I'm using an ESP-201 (also happens on the 01) and it gets into a weird state after a short time of network activity.

For my use case I am sending about 500 bytes every 5ms (this has a 1 byte response). This works for between 5 seconds and 15 minutes and then it goes into a really bizzare state. The remote app sending the data times out due to lost connection, but the ESP still sees the socket as open, as the ESP is in single client mode, I am then forced to restart the ESP if I actually want it to do anything.

At this point I have already commented out the code that processes the data coming in, so all the ESP is effectively doing is assembling the packets, and responding with an OK byte

Anyone know how I would get the SDK to compile a single function? I want to be able to send code over the network to the ESP and have it run the function already compiled

Ie. void SetupData(char* pData, uint32 Frame) This would populate data based on frame, but I want to be able to upload this into ram at RUNTIME, not just compile it into a function that would eat up space

Hi,

Me and the fiance are getting married next year and we want to supprise her mother with something special. The only photo left from her parents wedding is rather beaten up, I have tried myself with very poor results. Anything that can be done would be appreciated

http://imgur.com/ft4lItN