Dutch_Razor

I heard that having GPT Image 2 make 3x3 storyboards really improves Seedance's output quality.

For Seedance 2, I only see the option of image ref to video, which treats the storyboard as the first frame of the video. Or am I missing something?

https://americanexpress.com/nl-nl/referral/fb-gold?ref=fABIEBs87h

So I've been smoking some spareribs on my pellet grill to 92C and haven't had a really great success yet, one time they came out quite dry and one time the bark was so thick there wasn't really any meat left.

So conventional wisdom apparently says it's nearly impossible to temp spareribs.

Has anyone had success using the CPT? Maybe at a different temperature to account for the bone?

I was wondering if people wash their portafilters on the pitcher rinser. I have an Aliexpress rinser, however when I put the portafilter on it the water shoots through the basket creating a fine mist and a big mess everywhere.

Wondering if I should upgrade to a spinjet or that this is common.

So I modded by damaged B&O Penta speakers with a Icepower 300AS1 amplifier.

Works and sounds great, except the Audio Sense inputs seem to turn off the amp when listening to music at low levels.

Would it make sense to use an opamp with 2x gain in order to boost the audio signal going to the sense inputs? If I understand the datasheet correctly the OPA1632 should do the job. http://www.ti.com/lit/ds/sbos286c/sbos286c.pdf?ts=1587993568636

Thanks.

Hello all,

I was recently looking at the Ultimaker 3 and S5 series ( we have one at work), and the way they do leveling seems quite neat.

They actually measure the capcitance between the bed and the nozzle, then react when the capacitance changes if the nozzles touches the glass bed.

Did anyone ever try to put this sensor on a Reprap?

I noticed this during a train ride with intermittent 4G.

If the connection is lost while opening a link, Apollo will keep trying to load the page. If you press back and reclick the link it loads instantly.

Hello,

Normally I update software via Twincat as usual. Now I'm working a machine whereby the operator would update the software themselves, preferably without using Twincat.

Does anyone know if it is enough to replace the .app file and reboot the PLC? It'll probably work but would that be recommended?

So , I installed patch 1.09 today. Before that, had zero issues running the game.

After installation , game freezes about every 5 minutes, only thing left to do is end it in task manager. After setting the game to run as admin, I get the same issue , but now with "DXGI Error Device Removed" error.

Any ideas? Thanks!

Specs : i7-6700k, GTX 1070, 16 gig RAM, all factory clocked..

Hey all,

I haven't yet found a good source for curing salt here in the Netherlands. According to Chefsteps, it's a combination of sodium nitrite and sodium chloride (normal salt). (https://www.chefsteps.com/ingredients/prague-powder-no-1)

Does that mean i can just buy food grade sodium nitrite and combine? It also seems way cheaper, e.g. a 1kg is 8 euro over here: https://www.deoplosmiddelspecialist.nl/kopen/natriumnitriet

What are your thoughts?

Dear all,

On my DIY printer, I've observed some strange phenomena in my prints:

http://imgur.com/ImkNt70 http://imgur.com/2RrYrJo http://imgur.com/roPT7K1

Due to the lack of top infill, I would say it could be caused by a lack of extrusion, but increasing it by about 10% didn't really help.

On the other hand, the bed was not levelled perfectly for this print, but I don't imagine that would be visible after so many layers of printing.

Any ideas? Thanks in advance!