Prafe

For any Transcend Micro 510 (or Micro I assume) users, no need to dig out a windows PC and struggle with drivers to change your settings!

Transcend seems to have quietly released this short video https://m.youtube.com/shorts/qhZhTYgkCLA with the instructions for this feature in the latest update of MySleepDash.

Note that this does NOT work if your app is logged in. I did it successfully from a fresh install without logging in.

I was trying to order my meals for next week on the app and I was unable to find meals etc so I got on the website and wow the redesign has a terrible UX.

First of all everything is divided into nonsensical categories with local "flair words" mentioning tourist spots etc... It's as if they are using it to push certain meals over others perhaps?

And worst of all they removed filters!? I just want to see a big list of all the available meals and use nutritional and other criteria to narrow it down to a selection I prefer.

Anyone have any luck getting through to them? The AI chat is unhelpful and even refers to no longer existing website features.

I received a replacement screen for my XP2.0 and it seems they shipped a unit with the wrong firmware. I am unable to change p08 from 32. The previous unit had 32 and 100 as options to bring it up to Class 3.

Did this happen to anyone else? https://i.imgur.com/mVsh0SV.jpg

Searching online/reddit has not yielded anything specific to the high performance dish which has a much higher power draw (300w peak, 74w average observed on AC power).

I would like to power one of our units with our existing 14V (could be 28V) battery packs (small enough to fly with) and would rather not deal with the additional bulk and inverter losses. I have a spare cable I can splice into and hoping someone else has tried it and has recommendations.

I'm aware of the Tycon units but I don't see anything above 90w listed.

I get 20+ pool/handout feeds at a location via ethernet handoff and they’re just UDP multicast streams encoded with MPEG-2 at about 20mbps, similar

I’m trying to find decoders to replace a stack of Amino H140s currently used for this purpose. Ideally I need an SDI output so I can take the HDMI/SDI boxes out of the chain. The H140 works ok but the power supplies constantly fail, they require HDMI to SDI conversion and they only supports 2 audio channels when the streams have 8.

I also have an old ATEME DR4000 IRD I use for “broadcast quality” needs but it’s overkill and too noisy for the location I need these.

Any ideas?

Also on the lookout for cheap SRT HEVC decoders that support the

I’m setting up an XDCAM deck at a remote office and I’d like to feed it time code from an NTP source.

I do have Leitch master clocks at the other location but I’d really like to get away from such an expensive setup to feed timecode to a single remote device.

Anyone know of any devices or solutions that aren’t a full ESE or similar master clock?

I have an app on my phone called TC toolbox that I’ve used to jam clocks in the field with a headphone out adapter. Surely someone has made an inexpensive device or maybe an R Pi package?

My battery died the other day (that stupid cargo area light got turned on unloading and had not used the car for a while after that)

After boosting the the battery the vehicle exhibited a bunch of odd behaviours.

• switched to KPH from MPH (car is originally Canadian hence no TPMS) no big deal switched it back.
• first two startups the automatic up/down windows didn’t work. It resolved itself in third start a couple days later.
• TPMS light is on which is odd considering 2015 models in Canada do not have TPMS

Anyone ever run into these issues? I was assured my Outback does not have TPMS by the dealer when I originally brought the car over to try to get it enabled to meet US requireme

I recently acquired a standup paddle board to participate in a socially distant activity. What are some good spots to launch from that have (open) parking nearby?

I would normally go to Hains Point but I’m pretty sure the parking lot is still closed. Any ideas?

I’m sure many of you are in a similar position. My employer is asking us to disinfect gear coming back from the field.

The issue is that as far as I know, bleach solutions etc are quite corrosive and I’m afraid to damage cameras etc. Any ideas?