mr47

u/mr47


r/hometheater•

I've done some research, and know that the knee-jerk response to such a question is "DON'T". However, I have certain limitations which can't be avoided, and I'm simply looking for the approach that will maximize sound quality in this situation.

  1. Having a media wall is a hard requirement from my wife - she won't budge from this. And frankly, given the planned TV size and its placement in the room, just having a smaller TV stand and placing the speakers on the side would hardly resolve the issue (the speakers would still be squeezed (relatively speaking) between a wall and the TV cabinet on one side, and a kitchen cabinet and the TV cabinet on the other side.
  2. The speakers cannot be moved
06

r/MechanicAdvice•

Hi,

When I was about to replace the valve cover gasket, I found out that I can't take the bolt that's holding the ignition coil on cylinder 3. The bolt spins, but it's not coming out. I assume it's stripped.

I think I should be able to pull it out if I pull on the ignition coil while turning the bolt... I have tried for a bit without luck (and maybe it's good that I didn't succeed, as I need the car to be in driving condition, and wouldn't be able to put the coil back). If that won't work, what would be my next course of action?

And the bigger question - once I manage to get the bolt out, is there any fix I can apply, or do I need to replace the valve cover? Not the end of the world, but

14

r/Esphome•

Hi,

I created a new custom component that allows controlling Marpou lights via ESPHome (Chinese lamps controlled via BLE).

However, there are a few things I don't seem to understand about coding ESPHome components, and help would be appreciated.

  1. How can I access the Entity ID from my component's code? Case in point - these lights use a 32-bit field to differentiate between them. The pairing packet (accepted by the light for 5 seconds from physical power on) contains that field - and thereafter, the light will accept control packets that contain that 32-bit number. I'd like generate a different number per an instance of my component class, based on the entity ID. Basing on entity ID (an
32

r/MechanicAdvice•

A few weeks ago, I replaced the plugs on my NC Miata (MZR 2.0 engine). Put in the correct NGK Laser Iridium plugs, verified the gap on all 4 plugs before installation. Since then, 2 things have changed, that seem contradictory to me:

  1. The fuel economy improved substantially, with similar driving conditions and style
  2. The engine feels weaker - specifically, it's hesitant at lower RPM, has less torque, stuff like that.

So my question is - can these 2 changes come together, just from changing the plugs? Or am I imagining one or the other?

Thanks ahead!

23

r/CarAV•

Hi all,

I'm having issues after installing a new infotainment unit for my father-in-law. The car is an '08 Chevrolet Silverado 3500 HD (LT trim). His previous radio was an aftermarket unit with navigation, specific for Silverado. It wasn't working for a while. The system I'm installing is a BOSS headunit with CarPlay/Android Auto support (BVCP9685A).

Upon installing the system, the sound is very weak, and only coming out from the tweeters on the A-pillars. There are woofers in the front and rear doors, and no audio is coming out of them whatsoever. I came up with the following potential reasons, and I'd like advice regarding which of those don't make sense (and therefore aren't worth inves

10

r/hometheater•

And yes, the receiver is configured correctly (front speakers set as large, and bass is set to go to speakers, not the sub).

*TL;DR:*

Replaced my front satellite speakers from a 5.1 speaker system with second-hand towers, and it feels like the sound coming from them is muffled a bit. What should I do?

*Details*

I've been happy with my home theater setup, using an AVR (a Yamaha RX-V381 until recently, now Sony STR-DH790) paired with the Boston Acoustics MS4000S 5.1 speaker set (5 satellites + a nice sub). Everything worked well, and I was very happy with the sound quality.

Recently, I had a chance to put my hands on a couple of tower speakers (the sticker says "Peerless", but I'm not

219

r/MechanicAdvice•

So, I'm about to do my brakes for the first time, and the only thing that I'm missing is brake cleaner. Unfortunately, with quarantine all around, getting it from a shop is problematic. I do, however, have a can of MAF cleaner and a can of throttle body cleaner. Looking up those combined with brake cleaner brings up tons of questions asking whether you can use brake cleaner spray on MAF/throttle body, but I'm wondering the opposite: is it OK to apply one of those to brake lines, calipers, etc. - essentially, all the parts that should be cleaned when replacing the pads?

Thanks ahead!

18