Micron Rev.E (E-die) overclocking at low voltages
Tried to x-post but not allowed here, original: https://np.reddit.com/r/Amd/comments/d5e4gb/micron_reve_edie_safe_but_performant_overclocking/
Posts that were useful in my adventure:
- https://np.reddit.com/r/Amd/comments/csno8i/cheat_sheet_memory_timings_for_micron_edie_2x8gb/
- https://np.reddit.com/r/Amd/comments/cmcbc3/ocing_micron_edie_aka_subtimings_matter_a_lot_for/
Since I got my system a couple months ago I have gone along the journey of overclocking this kit: 2x8GB Crucial Ballistix Sport LT BLS2K8G4D30AESBK , which are Micron Rev.E, rated for 3000C15 and cost less than 80€. Initially, I was disappointed I could not hit any of the 3600C16 settings everybody was claiming was possible, no matter how much voltage I gave it.
Turns out the issue is exactly giving it too much voltage, and there's not enough information for it going around.
My clocks and timings are are hit at 1.33V, which shouldn't ever cause heat issues as that's even less than what my XMP profile set them at. They were achieved on my system with a Ryzen 3600, and the timings were plug n play for another system with a 3700X, passing hours of MemTest ran on the DRAM Calculator 1.6.1. Might not be enough for some, but enough for my intended use.
These seem to be safe settings that should work for anyone with Zen 2 and this kit, so I wanted to share them for people who don't want to go through the trouble and just want some nice safe presets. Remember that these are not super tight, especially tertiary timings.
Hardware and BIOS:
- Ryzen 3600
- 2x8GB BLS2K8G4D30AESBK rated for 3000C15 running @ 3600C16
- MSI B450 Gaming Pro AC with 7B85v19, 1.0.0.3AB (no longer beta FYI)
Results achieved in AIDA64:
- 70ns latency
- 50700 MB/s read
Settings:
- I am giving -0.05V Core offset voltage until ABBA is available for this board at which point I will re-evaluate it
- 1.025V for SoC Voltage
- Cool N Quiet is enabled here
- 1.33V DRAM Voltage
- VDDP 0.900V
- VDDG 0.950V
- Give a little more boot voltage if your board has that option (this one does not), very rarely my system won't cold boot
- Command Rate
- Always try Gear Down mode first
- Try 1T at the end by setting ClkDrvStren to 120 Ω (thanks to this amazing post)
- I couldn't get tRC lower but you can try it, I think that along with tRFC are the bottlenecks for Micron Rev.E
- Extra settings:
- PowerDown disabled
- BankGroupSwap disabled
- BankGroupSwapAlt enabled
- ProcODT 40 Ω
- RttPark 48 Ω
- RttWr / RttNom disabled
- CPU SVM mode - if you use virtualization you will have a penalty in RAM performance, at least with my board
Posted Sep 17, 2019, 10:29 AM UTC
Thanks for sharing! Tried it yesterday on 1,33v with the 32gb version of the Kit. 3200 is running at 14-17-14-14-36-56-520. for rtc and ras i basically can set whatever i like - since it is probably overwritten at some point. trfc and rrcd is my wall. 3600 is running at 16-19-16-16. also 600 trfc.
since 3200 is stable with t1 and really tight subtimings and if something fails i can tune things down a bit and 3600 is quite borderline with geardownmode and more loose timings i'll stick for the 3200 setting for now.
thx for sharing again. would have probalby never tried just to slam 1,33v into the ram and hope for the best.